I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
HI.
I am trying to implement the mass storage example (zephyr/samples/subsys/usb/mass in the 2.2.99 SDK) on the nRF52840 dongle for windows 10 but using an internal RAM...
Dear support team,
Currently, I create a custom board using nRF52833-CJAA SoC, but I not found nRF52833-CJAA package in nRF Connect SDK v2.7.0.
Could you please help me...
I'd like to make my product appear as a USB drive when plugged into a computer. I want to save sensor readings to CSV file, and allow users to read/copy them.
I found the...
I am currently working on encrypting "Provisioning public key PDU" with a public key of end node that was received out of band the by provisioner before transmitting it to...
Hi, all:
I use 9160DK to test GPS standalone mode as follow steps with AT command example：
Approach 1:
1、set ”AT+CFUN=0“ to power off mode;
2、set " AT%XSYSTEMMODE...
Hello,
I am using three nrf52840 DKs to test sending gatt notify data. They are one peripheral and two central.
When they each have only one Gatt Customer Service, peripheral...
Hello,
I'm facing a problem in pc-ble-driver-py. I adjusted the uuid_count, but the code still fails at the service discovery line:
ble_adapter.service_discovery(new_conn...
I try to use st25r3911 and try to achieve low power consumption.
The code configures interrupts: gpio_pin_interrupt_configure_dt ( & irq_gpio , GPIO_INT_EDGE_TO_ACTIVE ...
Hello,
I work with the Zigbee Light Switch exemple from SDK 2.7.0
After association, the device never use the Poll data as for end_device role. But, it sends continuously...
We have created Thread Network include Leader, router and end devicewitch nRF SDK v2.5.0 on nRF 52840
We found the Thread connect will offline after 15 minute and not reconnect...
This is a higher-level question because I'm having difficulty finding concise and clear practices for this sort of thing. I don't want to go implementing something subpar...
Hi folks,
I'm making an application which needs to transmit a few kB of config data (for a configuration utility), and I was hoping to do it via UART.
To that end, I loaded...
I am working on specialized PCB's for my job, and we are trying to capture modem traces for our devices. Via JTag, I have serial access to pins P0.05 (TX) and P0.06 (RX) of...
Hi All
I m developing a project in nref9160, in GNSS part, I need to use PGPS, but can I control the checking in nrfCloud? sometimes it go to download PGPS and make GPS...
Dear Nordic Developer Zone,
I am working on MAX30003 ECG ( https://datasheets.maximintegrated.com/en/ds/MAX30003.pdf ) with Nrf52840-DK. My sensor is work on the 32.768kHz...
