the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi, we are writing the register TASKENTERSHIPMODE to enter ship mode, and everything works ok. But as the ref manual says, when VBUS is present this task is ignored.
Is...
Hi,
We are working on the nrf5340 and our current device firmware uses the NCS 3.0.2 (i.e. nRF Connect SDK 3.0.2). We wanted to try an upgrade to NCS 3.2.1 and followed...
Hi, so my intention was to test the free subscription of Memfault with the thingy91 I created my account in nRF Cloud but the button to access Memfault is not there, I had...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi,
We’re looking for the SBOM and the official CPE identifier for the Nordic nRF5 SDK, specifically version 15.3.
We would need:
The SBOM for nRF5 SDK v15.3
The...
I am using the nRF52840DK with nRFConnect for VS Code. In Lesson 6 Exercise 1, I connected the DK to a BME280 board I purchased online. The board exposes the four pins needed...
I've been wrestling with an issue whereby I attempt to deploy an mcuboot image to a device and inconsistently I get a message that says the firmware image is not valid (error...
I am currently encountering an issue with BLE bonding logic in my application.
When a phone initiates a pairing request and triggers a pairing pop-up, I use the security_changed...
We have a custom PCB with a nRF9151 implementation supporting both LTE/NB-IoT and GNSS. The PCB has no switching regulators or any other possible noise source except for the...
Working the SDK intermediate course, L1.E1. (SDK 3.2.1 / nRF54LM20A)
After building, I select <Debug> under Actions in VS Code. I get this popup that says "Debug options...
Hi DevZone Community,
I am facing a build issue while working with the following environment:
Environment
SDK: nRF Connect SDK v1.9.1
Hardware: nRF9160 DK...
Hi,
As the subject states.
I would like to run the tests at zephyr/tests/drivers/spi/spi_controller_peripheral as intended in testcase.yml. I can verify that I have the...
Hi All,
Anyone has experience in FRAM?
I have a project which need to integrate the FRAM CY15B108QN with nRF52840. I got a weird result by using nRF silicone, but can...
Hi,
I wanted to use the `nordic-semiconductor.nrf-kconfig` and the `nordic-semiconductor.nrf-devicetree` without the nRF Connect extension in `vscode`, but they don't seem...
Hello, I am an absolute beginner with nRF9160. I have just received one development kit.
I am trying the Quick Start application for cellular modem with AT commands.
Unfortunately...
