We are using the nRF5340 with Zephyr OS v3.6.99-100befc70c74 and nRF Connect SDK v2.7.0-5cb85570ca43. We have the following questions:
Is our understanding correct that...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
I just obtained a PPK2. Nice to see an ARM native installer for nRF Connect on MacOS.
However, for the PPK2, only "Not supported yet" is displayed.
MacOS version is 14...
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
Hi Nordic Team,
I'm currently working on a BLE project using the nRF52840 DK with the nRF5 SDK (not using SoftDevice Controller), and I’ve run into a critical issue related...
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
I am trying to scan for sensors on an I2C bus using the nrf54L15 and Zephyr RTOS. I modified the i2c example from here: https://github.com/iFransL/i2c-scanner/tree/main
...
Hi,
I'm working on an application where the system should enter System OFF mode after some button activity and wake up (restart) on a button press or USB connection.
When...
Hello,
I’m trying to understand exactly how the location module works in the Assert Tracker V2 application. I want to see the NMEA data in the logs, but I’m not sure how...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
im trying to develop a prototype that uses a thingy53 and lvgl to draw a screen on a solomon ssd1306 attached via i2c (kwiic) but am having issues with getting it to build...
NCS 2.9.1 - NRF5340DK
I am trying to use multiple compare channels on Timer1 (output_timer) such that an interrupt handler fires for both compare values, the second of which...
Hello!
I'm new to Nordic Semiconductor and currently developing a project for which I need support regarding the nRF9151 DK . Before placing an order, I would like some...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
Hi,
I am working on implementing an I2C node in my nRF52840 based sensor. However I am getting the following kernel panic.
I removed all I2C node related code that I...
I used a mesh example (the example name is "mesh") for testing, and enabled low-power nodes using CONFIG_BT_MESH_LOW_POWER =y, and disabled the automatic start of low-power...
I used ncs2.9.1. I download the mesh dfu distributor and mesh dfu target examples to two devices respectively, and successfully updated the mesh node through shell commands...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
Hi, I have a nRF5340 using hci_ipc that has the following features:
Central Role + Scanning (Multi-connection to nRF52840 peripherals)
Peripheral Role
QoS Channel...
