Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
I have an nRF52840 design using the chipscale package. I have very little I/O so it can all be placed on the outer ring to avoid the blind vias needed for the inner ring....
I am working on a BLE to ANT (Specifically FTMP to FE-C) gateway.
HW used is the pca10059 dongle.
Windows10, Programmer 3.0.4, Segger 5.42a.
SW is nRF5_SDK_17.1.0_ddde560...
If I have multiple peripheral devices, advertising at the same time with NUS service, what factors determine to which peripheral, the BLE central connects?
How can I configure...
Hello everyone.
I'm developing a custom board mounting the nRF5340, and I want to use the micro USB. I was looking at the schematic of the DK for reference, and I found...
Hi,
Not sure if this is the correct place to ask...
My code is crashing after a spi write function.
It is probally obvious to someone here, i think i fell into that...
I'm attempting to merge 3 HEX files into one using the Merghex command. The "BinaryImage access" error appears, see the screenshot below.
I've tried this several times with...
Hi,
I'm porting my SSD1333 (Solomon IC for OLED displays) code driver to Zephyr OS drivers for ease of use along with LVGL (going from `< nrfx_spim.h>` to `<drivers/spi...
I want to transfer a bunch of data over the virtual com port to a PC using the USB port on the nrf5340. I'm using the CDC ACM sample: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
why
AT%XRFTEST=1,1,14,7880,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7930,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7980,23,1,4,0,0,0,0,0,0
returns ERROR but e.g.
AT%XRFTEST...
We are trying to see if it is possible to detect a vibration using the ADXL362 accelerometer on the Thing:91. We have it setup to to trigger on motion, but we need to be able...
Dear all
I following the example here , over the air one, and get it basically working, thanks for the tutorial.
Now I have a few questions:
1. It looks like it always...
Hi
I am studying Matter, my setup is
chip-tool : chip-tool-android_armv7l.apk v2.1.0
OTBR : raspberry pi 3b + RCP( PCA10059 )
board : nRF52840-DK(PCA10056)
sample...
My pairing is working and shown as bonded on Android, but when the DK is reset, the bond is no longer valid.
In studying saving of bond information, I find references to...
