Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi,
I m using SDK 2.9.0. After building and flashing my target board based on nRF5340, I get the above kernal panic error.
This is my .config.
and my prj.conf
Are...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for BLE scanning and advertising. scanning and advertising is working parallel. this is controlled by other MCU over serial...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
Hi, I'm using nrf52840DK.
I set the selective_auto_ack as true. It should be able to adopt dynamic ack (or ack payload).
I have two data packets, which are ch_pkt and...
Hello,
I try to figure out, why a certain IO pin shows some pattern at startup. After using JLinkExe to set a watchpoint at the configuration register of the pin (GDB was...
I am trying to update my firmware using IOS-nRF-Connect-Device-Manager and am getting an invalidHeaderMagic error when calling: I am using version 1.7.3 (last version to still...
I'm attempting to use the Settings API save and retrieve data from nRF52832 FLASH memory. I can build and run the example application provided in the Settings documentation...
Hello Developers,
I am working with the nRF52833 microcontroller using segger embedded studio with the latest SDK. My issue is that I can configure and use all GPIOs except...
I have browsing this site, no clearly answer found, but,I think someone has done this job before.
My scenario:
.many BLE client (5.0 above);
.BLE clinet will upload...
Hi, We have an application running on the nRF53, and would like to change the BLE MAC address from the default Random Static Address, to a Public Address with a valid Vendor...
I'm studying with PCA10059,trying to build a gateway between BLE peripherals & PC.
For PCA10059 has build-in USB socket,and I will plug them into PC's USB ports at last...
Hi all,
I want to use UART periodically, but because I need to communicate with other standard UART, I cannot use LPUART
I saw that Zephyr's demos all use CONF_SERIAL...
I am following all the steps given here: nRF Sniffer for 802.15.4 but my zigbee sniffer did not show up. When i did the steps given there for ble sniffer it showed up. steps...
Hello,
I am new to developing with Nordic products and I have a question regarding the components in the antenna matching network. I am designing around the QIAA QFN-73...
