Hello, Under Windows 11 Pro, nRF Connect SDK v3.4.0 fails to compile builds with error "CMAKE_BINARY_DIR length (109) exceeds 90 characters." The same build on Windows 11...
We're implementing a PAwR (Periodic Advertising with Responses) based onboarding flow for a large fleet of devices (target: 200+ nodes, eventually scaling to 1000s) and are...
Hello Nordic Support Team,
We are using a Fanstel module that integrates the nRF5340 BLE SoC and nRF7002 Wi-Fi companion IC in a single module.
We have manufactured approximately...
Hello everyone, I'm working on a long-distance communication application (>50m).
My hardware is nRF52840, PA/LNA: RFX2401C, ceramic antenna: AN9520-245.
I've achieved...
Hi:
I use ncs3.3.0 and nrf54l15dk.
PC BLE pairing nrf54l15dk failed log:
prj.conf
But with BT configuration, turning off ESB related content, it can be paired...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
Hello Nordic, Our procurement team is worried that the nRF52832 has reached end of life. I wanted to confirm if this is the case? If this is not the case, when is it expected...
Hi, community.
From the official document, I have learned how network core Bootloader works.
It can write data from shared SRAM to the corresponding flash address of Nework...
Hello,
i'm programing a nrf52832 and a nrf52805 and I'm using the peripheral uart example, I would like to change the size of the bytes of my rx and tx that I can send...
Hi
I have a board nRF52840 configured with some QSPI with filesystem configured
I would like to manage the file system from an app and I saw that - nRF Connect Device...
I'm working on a project where we need to store into FLASH about 1350 bytes of compressed data at about 2HZ (twice a second). This is my first Nordic/Zephyr project, so I...
Hi
I'm working with an nrf52840-dk on NCS 1.8.0.
I'm attempting to interface the board with an LS7366R quadrature counter over SPI; however, I'm not receiving any count...
hello Nordic
i am using ppk2 pca63100,
working on linux (manjaro), installed the nrfConnect v3.9.3 with power profiler v3.3.0
1. when i connect a device i have to...
This question relates to the unsatisfying reponse to ticket 283390.
The technology of the processor is not important. Arm Cortex processors are as fine as several others...
I am having trouble setting up a GPIO pin that will toggle when the radio is active on the network core. I have tried adding the code in bluetooth.c from the ppi_trace sample...
Hi everyone!
I am developing a board using a nrf52 as a BLE interface for an arduino. My idea in the future is update the firmware of the Nrf52 with OTA. But i wanna do...
Hello everyone. I am trying to set up a BLE central-peripheral network using nrf52840 based on NUS service. I need up to more than 10 peripherals which is customized board...
Hello there,
I'm trying to make a transceiver simulation on nRF24L01+ using Simulink. The block diagram provided in the documentation/datasheet was not clear enough for...
To create the prototype of a computer, which follows a non-von-Neumann-architecture, I am looking for an "Building Kit", which allows non-standard connections between computer...
Hi,
I'm trying to build my own "auto sleep" mechanism based on timers.
This is my code:
The timer works as expected, but when the soft_sleep function is reached, the...
We have a device that we are trying to implement an encrypted data transfer on. We wanted to lock down all the characteristics until we write a passkey on our security characteristic...
