Hello Nordic team,
I have a question regarding the Bluetooth LE RF-PHY Intermodulation Characteristics test (Bluetooth Core Specification Vol. 6, Part A, Section 4.4)...
I am developing a custom nRF54L15 board using a GigaDevice GD5F1GQ5REYIGR SPI NAND connected through the nRF54L15 sQSPI/MSPI interface.
I have encountered a highly reproducible...
Recently the VSCode extension has seemed to become extremely slow / unresponsive when triggering a build
Judging by the vscode popup on every build telling me there's an...
I am unable to perform a fota on an nrf9160 based device in the field since my nrfcloud account was updated to require the use of the new memfault based version. There was...
Hi,
I just read the nrf54l15 errata [100] of the nrf54l15. It's actually a huge issue, as we do have an interrupt line on one of the affected pins, that is active low, eg...
Hello, We're in EMC testing for a host product built on the nRF9151 (LACA A1A, FCC ID 2ANPO00NRF9151), running modem firmware mfw_nrf9151-ntn 1.0.1.
For our lab build, we...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
Hi Everyone,
Hope you all are doing well.
I'm using nrfConnect sdk v1.7.0 and vscode for development.
controller : nrf52833
Here I tried to build image with bluetooth...
Hi. I have been using this document to work on the Fanstel USB840F device. USB840F_User_Manual (squarespace.com) After erasing the device, I could'nt run this below command...
Hello, I am developing a custom board using the nRF52810 WLCSP package. I realized I made an error in the board layout after placing my order, the error being that I placed...
I made a DFU Bootloader for my nrf51822 that waits for two seconds before starting the application, so I have time to connect and flash.
That process was working with the...
If I set two separate UUID scan filters as below:
Is it possible to discern which event triggered the filter match?
At the moment on the scan_filter_match callback,...
Hello,
it's a nice concept to include sensors via the device tree and simply enable them in the project file. But I feel like I'm losing control of the sensor a bit. I don...
Hello nordic. I've been using the PPK2 to measure the current draw of the nRF9160DK. However, spi peripherals are not included in these measurements. I was told that if you...
Hi
I´am pretty new with the nRF connect sdk. I want to check the features from BLE long range /coded phy.
In the past I have allready worked with the ble_att_mtu_throughput...
hello Sirs
How can I put nrf5340-sdk in to extended mode to transfer 250 bytes of data over BLE radio?
the sample code I am using is Peripheral-uart example code.
Excuse me:
I want to implement nrf52833 run FreeRTOS，The nRF52840 project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos\pca10056\s140\ses can only...
Hello All,
I am using NRF52833 in my project. I am also using RTOS in the code. I was previously working on NRF52840 but now I have migrated to NRF52833. I have changed...
I'm new to using NFC.
I've tried downloading a few NFC sample programs to my nRF5340-DK board and playing around a bit, but I ultimately want to implement something like...
We are using nordic SDK 16.0.0 and mesh SDK 4.2.0 with a nRF52840 chip.
Our products already have the provisioner/provisionee and config client/server implemented, based...
