Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
Summary
The Zephyr RRAM driver drivers/flash/soc_flash_nrf_rram.c does not pass NS-side reads of TF-M secure flash through soc_secure_mem_read when the device tree uses...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
Hi,
I am a new beginner when it comes to Thread and Matter. I am trying to run Matter on nrf52840. I flashed the door lock example, commissioned the device using BLE and...
I am using SEGGER Embedded Studio and an nRF52-SDK circuit board to run example ble_central\ble_app_hrs_c from nRF5_SDK_17.0.2. I have a peripheral that reports motions. The...
Hello Nordic, We are preparing for mass production with nRF9160. We have a script to flash, register the thing on AWS and write credentials on the modem using nrfjprog. We...
Using the debugger in SEGGER Embedded Studio and two nRF52-SDK circuit boards, I am stepping through code from the nRF5_SDK_17.0.2 examples.
Very often I end up in file...
Hello everybody,
I'm working on a Project with nrf52dk(nrf52832), and sdk 15.0.0 where I need to read the data from multiple sensors with twi/i2c and send the data via ble...
Hi,
is there a possibility to check in waht CE-level (ECL0- ECL2) the modem is operating on? I know that the ECL is decided by the network and not the UE. However it must...
Hi, I have a problem with simultaneously working Bluetooth LE with LTE. I've use nRF52832 as a Bluetooth controller with is connected to nRF9160 via Low Power UART HCI. When...
Hello I have a few issues which i can't handle. Platform: Visual Studio Code on Windows 10 Board: nrf52840 dk
In my project i need to create workspace which few different...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.5.1 to 1.6.1) and the Modem firmware (1.2.3 to 1.3.0) on my nrf9160 DK device (v1.0.0, SiP revision 2...
I want to use the nRF52840 in the High voltage mode. In this mode as per my understanding, both regulator stages needs to be used. As per the datasheet, configurations given...
Hi all,
I want to update my application with the newer NCS 1.7.0 version. I've changed my west.yml, which containing only NCS-SDK as the only dependency. After running...
Hi,
I would like to setup vscode to develop nrf applications. However, I'm having a problem for the installation of the nRF connect SDK in ubuntu 21.04 (Hirsute Hippo)....
