Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Dear Nordic,
we are developing DFU Secure bootloader for a nRF52832 based HW.
We are starting from the "\examples\dfu\secure_bootloader" . First of all, we succesfully...
Hi,
Actually in my program I have a serial uart interface that cause an interrupt when a message is receive. During the interrupt, I send a mesh model command and its works...
Here I use gpiote and Ble_template_example.
The advertisement code is working fine but now I use button interrupt to send different payload or the button press change...
My understanding is that secure boot calls an interface to make portion flash that contains a bootloader immutable. Since this is called after the bootloader start to run...
Hi,
Please suggest us Bluetooth online course which is available. Also if there any BLE materials please share me a link so we can go through.
Thanks & Regards
Pavan...
I have functioning firmware which produces 0xdeadbeef if I halt debugger. Is it not intended by the SoftDevice in normal operation?
How to debug this issue?
Hi
1. I am trying to use the main.py for sending command to my power profiler kit II
does it requires to use JLINK (Segger) ? I get an error a message No Emulator connected...
We would like to pre-bond our devices in production by writing bonding data into flash. Generating LTKs is easy enough. But we'd also like to store that notifications on peripheral...
I've just received a nRF9160 DK.
I've installed nRF Connect v3.6.1 and LTE Link Monitor.
I select the device (3 serial ports are shown). I press reset button and the terminal...
Describe the bug
When trying to sleep core on NRF52805 using low frequency internal rc oscillator, average current consumption is ~189.50 uA while when using external crystal...
Hi. We have nRF9160 DK using Serial LTE Modem as standalone modem for CAT-M1 connected with external nRF52 via UART2. We have setup the modem to establish connection to AWS...
I used the nrf52832-QFAA Reference Layout as the base design for the PCB.
The changes I made were:
1.) Added the DS1339 RTC Pin P0.22 will be configured SCL and pin...
Hi,
I am using nRF52840 dongle. The REG_OUT is programmed to 3.3V by default.
I am planning to use Li ion battery at VDDH. When the battery discharges below 3.3V, is there...
I have an issue when i am using an iPhone 8 instead of iPhone 7 , I can use iphone7 to OTA my BLE UART by NRF tool box, but ,when i useing iphone 8 , it does not work, what...
Hi,
Please advise.
I am using (nRF5SDK160098a08e2) , nrf52840 .
This is my code to change name in Runtime not via restart or timeout.
I call the function below every...
