Hi,
I am experiencing an issue where SPI read operations fail after upgrading from NCS 3.2.4 to NCS 3.4.0.
Hardware:
Custom board based on nRF52840
ADS1294...
Hi:
I use ncs 3.3.0 and nrf54lm20dk.
USB mode running phenomenon: Mouse stuttering.
But use ncs 3.1.0 mouse is very smooth.
Since the ncs3.1.0 version does not support...
Hello,
We have a project currently using NCS v3.2.3. We delivered the first production series of 50 units already, with the NSIB from this NCS version. We use the NSIB with...
Good morning everyone.
I’m having some issues compiling my firmware using NCS 3.4.0 and the ‘ns’ option. I’m using an nRF9151DK board. Basically, my firmware compiles and...
May I ask if the nRF54L15 comes with a default state when shipped, or is it blank? Also, what’s the GPIO status? I’m asking because it will connect with the AP, and I’m worried...
Hi,
I am using NRF52832. I Have two doubts to clarify about internal flash
1) I have done the flash write of the timestamp in a specific address of internal flash. its...
Hello,
I an using a PWM and sampling 2 ADCs in scan mode. I want to read the output of the PWM as an ADC, kind of like a feedback. Is it possible using PPI.
Thanks
Hi,
I am using an NRF 51 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the ble_peripheral...
Hi Nordic devs,
I guess this is more a suggestion than an issue: The power profiler kit II software, when operating in "Ampere meter" mode has the power switch connected...
When I save the conf file with the following contents and select the corresponding project from `nRF Connect Options`, an error occurs and the project cannot be opened. Please...
Hello, I'm trying to port my working project from 52811 to 52832 Both are on SDK 16.0.0, SD 7.0.1 Here is the advertising code that works on 52811 :
This code crashes on...
Hello!
I'm tinkering with the NCS libraries, and I'm really liking the way this is turning out coming from the nRF5 SDK! My question is what is the best practice for creating...
Hello,
I am a newbie and trying to setup nordic thingy 91. I have booted the updated version of modem firm ware and also the "thingy91_nbiot_2020-10-30_5522ca2b.hex" file...
Hi Community!
I'm working on product development for a client/customer. The product will be a small embedded system with an LTE chip (nRF9160) and a BLE chip (nrf52840)...
I'm having a lot of confusion with using TWI on this chip. I have been running example code that I found in this tutorial nRF5 SDK - Tutorial for Beginners Pt 35 B - TWI ...
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 I follow the link above to create a hello world project, which has failed all the time. Here is the...
SDK16.0.0 + Mesh SDK 4.1.0
Help, we have developed our own board with a Fanstel BT840X module. Some of our boards are asserting ("Softdevice assert: 154516:0") and I am...
Hi Nordic,
I'm using nRF52 DK (PCA10040). I tried to copy and paste the project from this default location:
...\nRF5_SDK_17.0.2_d674dde\example\peripheral\twi_sensor ...
Hi,
I managed to compile and run(?) my first two programs for nrf51 dongle on Keil uVision, however while i think they run I cannot make the debugger work and see what they...
Any suggested APIs to setup BLE transmit power in NCS?
the set_tx_power() in the Zephyr example looks not work with nordic softdevice controller.
https://devzone.nordicsemi...
