Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I used this user guide: https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf .
I am using the nRF52840 DK for the sniffer, and managed to connect it and...
I changed the IO of the SPI and could not receive the data.
Hardware: nrf52832 DK two
Software: nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi and nRF5_SDK_17.0.2_d674dde...
Hi,
I'm developing an application for the nRF52840 that uses 3 SAADC channels. In particular, the channels are configured as below:
I'm able to get the samples from...
It is unclear, for both the Thingy 91, version 1.0.2, and nRF9160-DK, version 0.8.3, if they need bias-tee's for use with an external active GPS antenna. Also, what about...
Hello, I have problem and I hope you can help me.
I have 3 sensor nodes. every node has an IMU sensor and nRF52840 microcontroller. These nodes send the IMU data to the...
We bought 4 NRF5340 PDK and trying to setup BLE mesh. As suggested in the getting started guide, there are two BLE mesh example samples from nordic and zephyr. However, for...
My code uses the nrfx SPIM driver. This gives you the option to use interrupts or not. Interrupts are great for long message transfers, allowing sleep while waiting for the...
SDK 14.0 +nrf52832:
We use phone to send command to our toy(nrf52832) every 100ms to control a motor accurately,mostly toy received command is long than 100ms(more than...
Hi, Is it possible to order nRF5340 QKAAD0? This one is on DK and the last IC version? As I can see, your distributors e.g. Mouser only have nRF5340-QKAA-AB0-R/R7 but this...
Hi,
I am using nrf52832 development board with s132 softdevice and SDK17. I want to add the DFU service to this application so that I can update the firmware to the device...
Hi,
In the Enhanced Shockburst User Guide, there is a brief discussion about the required bit pattern of 1st on-air byte of the base radio address
(which immediately follows...
If I use nRF Connect to connect to the Peripheral and the Subscribe to Notification Characteristic I can see in the "Enabling notifications" in the log (however no notifications...
Hello
I use sdk v17.0 and nrf52832.
I'd like to use 1-channel PWM and 2-channel PWM. However, an error is output from the pwm_enable when using these two together.
...
Hi,
Following are my working environments:
Product: nrf51422 Evaluation Board
SDK: nrf5 SDK v10.0.0
IDE: Segger Embedded Studio
Programmer: Segger J Link
I was...
Hi,
We have a device that is using Nordic's ESB protocol. We want to use different frequencies to avoid collisions and for that we also need dynamic frequency handling....