Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
From Mesh Model Specification 1.0.1.
"3.3.2.2.2 Receiving Generic Level Set / Generic Level Set Unacknowledged messages If the Transition Time field is included, the Delay...
I want to send larger UDP packets from nRF9160 (Thingy:91) using Serial LTE modem app.
I am not able to send more than 288 bytes of binary data.
How to send larger binary...
Hello, first, a little background info:
devzone.nordicsemi.com/.../
I want to know if I have successfully set the CCCD handle or not with my Android program.
And...
I've seen the Connectivity Bridge Application in the ncs, however I can't find any sample application for the nRF91 side showing how it can send/receive data and events from...
Hello
I have a cheap ST-link that I use heavylly to program STM arm cortex chip.
So my guess is that it should work for this case.
I am following this tutorial:
...
Hello.
When I try to import a project , it will show a error. I can't build it . Pleave view following info and help me about it . Thank you.
Harrison
BR!~
Hello,
I try to add the BLE-Template code into my existing program code, but I get the following linkage error. I have defined the following flash_placement.xml for my Segger...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
Hi,
Add BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event handle at ble_lbs service in example of ble_app_blinky. but when client read the characteristics 1524 or 1525, no BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
Environment: Windows 10 nRF Connect SDK 1.4.0 I followed all of the steps described in nRF connect SDK documentation and tried to build "Blinky" sample from zephyr as shown...
use s132 on NRF52832
when i used sd_ble_gap_connnect () to connected peripheral device,it return NRF_ERROR_INVALID_ADDR
the addr copyed in scan_evt_handler() by NRF_BLE_SCAN_EVT_FILTER_MATCH...
Hi ,
I have made basic binary sensor based on light bulb project,
wanted to add default BIND-TO-Gateway ( Short address 0x000). Gateway is CLI_AGENT .
I am try to add...
select at_client folder
west build -b nrf9160dk_nrf9160ns -p
shows this warning
```
warning: The choice symbol LTE_NETWORK_MODE_NBIOT (defined at /Users/paul_tanner...
Hello, we are using a usb dongle where we have a NRF52840 and RFX2401 PA+LNA frontend. The latter can be controlled with TX_EN and RX_EN pins. Please see attached schematic...