Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hi,
I am trying to read and write data from flahs using the fds library. For the moment my main problem is that when calling fds_record_find, it returns FDS_ERR_NOT_INITIALIZED...
Hello,
is it planned to add support for PyOCD and/or OpenOCD for NRF9160?
If yes, when?
ATM (26.02.2020) they support only NRF51 / NRF52
https://github.com/zephyrproject...
I am trying to do multiple PWM in my DK board , but it cant work.
I made simple code for it .
This is my overlay file , but it works for just pin 13, means ch0 .
...
Hi,
Is there any way to tell when the modem has finished doing a band scan? I would like to know so I can swap between CAT-M1 and NB-IoT for globally deployed devices. ...
Dear
I am try to perform an OTA operation on a dongle of nrf52840 by ble_app_blinky for PCA10059 project and light-switch server for PCA10059 project, which works well on...
I've setup SDK 1.4 with Segger, however I can't get the Asset tracker Application to compile. It seems to be building the SPM even though the project is setup to use the Non...
I use the template for pairing and binding. For the first time, after binding, for the second time, I bind again, prompting to reject binding. How can I match and bind many...
Hi,
I want to compile and run Mesh examples. I tried the Light Switch client, server and the Sensor server examples. All of them fail when the linker is invoked. All of...
Hi everyone!
I'm new in Nordic DKs and I have a new Nordic Thingy 91, I understand that it uses two chips: nRF9160 and nRF52840.
Maybe this is a silly question but, can...
I have a custom beacon application that is mostly idle. Before adding a timer, the current consumption was 3.2uA. After adding the timer, the current consumption jumped to...
So far I've use the nrf gatt module for setting MTU and DLE and seems to be working, however this module does abstract packets and maximum tx time in a connection. There are...
I have incorporated the DTM example into my application. It works as expected when I set the NRF_POWER->GPREGRET and then perform a reset sd_nvic_SystemReset() , then enter...
Hi,
https://devzone.nordicsemi.com/f/nordic-q-a/67024/nrf9160-questions-related-to-immutable-mcuboot-application
From the above thread i learn that MCUBoot is not that...
To get the GPIO binding I can use:
device_get_binding("GPIO_0");
1. I would like to know where in the documentation it lists the strings you can pass to that function...
I am debugging the GPS function and referring to the sample code of the official GPS. As for the code of reading GPS data, I have a question that is the way of obtaining GPS...
