Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi,
using dongle nrf52840 pca10059 board name.Not able to load the hex file into the programmer app as using the nrf connect for desktop version:3.4.2.Getting the warning...
Hello
I use nrf52832 and SDK v17. And I'm using NUS (UART) service and peer manager. So far, I've been testing with an Android phone and connected it with an iPhone for...
Hi All,
I have modified ARM FB ABI type preprocessor macro to "soft" to optimize power consumption in my saadc routines. But I am seeing below error while compiling. I...
I am developing USB CCID driver class for nordic nRF52840. I used USB CDC-ACM class as reference and tried to implement for USB CCID. I have developed the device descriptor...
Hi,
I have a question of correct way to connect/disconnect/reconnect from the LTE network to save power.
I already know about PSM mode.
But In south korea, SK telecom...
Hello
I'm working on SDK v17, and I'm using the nRF52832 custom board. I use several APP_TIMERs. One of those timers doesn't seem to be working properly. Timer calls are...
I'm just finishing a BLE project for a client. The code is based primarily on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput. I'm using SDK 15...
Hi there,
We're using NRF52840 and nRF5_SDK_15.3.0_59ac345. We have a product where 2 nRF52840's have to talk to 1 device (say, an iPhone or a computer). We were thinking...
I've noticed when using the nRF Connect Software, after I connect to a perihperal, it immediately discovers services, but takes about 4 seconds to read the GAP Device name...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hello,
What the average data consumption for using A-GPS on the nRF9160 to download the Almanac and Ephemeris data? I would like to know how much data is billed through...
Hi,
I am developing a product based on SDK v15.3.0 and SoftDevice v6.1.1. my product acts as a BLE central device.
On the peripheral side, is an iOS application which...
Hi,
I need some help in explaining the GPS behaviour I am observing. In the following figures the GPS current draw is depicted.
For the specific scenario the position...
Hi,
I'm testing stability of my firmware. As a part of tests I'm trying to maintain long term (multiple days) connection between nRF52 and nRF Connect for Android app running...
