Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello
I'm working on SDK v17. Receives certain data from the app, and LED timers work according to the data received.
The code that receives data from the app and parts...
Hello
I'm working on sdk v17. I want the LED to be printed out like a wave when I receive certain data from the app. (5 Times)
It is simple to use 'delay' and 'for' as...
I had my first encounter with Nordic chips a couple of years ago. To evaluate the devices, I used an nRF52832 to implement a small helper project. I was very impressed: it...
Hi Team, Is it possible to use the BLE NRF52832 module for audio applications like attending phone calls, listening music etc. If it is not possible with this module could...
I wrote this code to make a 1MHz signal clock with timer and GPIOTE.
It works fine without softdevice, but when I modify my app to use BLE, gpiote doesn't work (I...
Hai ,
I am using nrf52840 and 15.2 SDK for ota over BLE. I have made bootloader for OTA over BLE and tested same with nrf connect application using dfu package zip file...
I tried to make a copy of the Asset Tracker example application to start my own project. However I cannot get it to load in SES. I'm currently on the Master branch of nRF...
Hello,
Based on the DFU documentation, you should be able to download an updated soft device as long as the "major" number of the soft device does not change. This was true...
I recently designed a PCB and have been testing it.The PCB mainly consists of the Bluetooth Module BMD-350 ( based on NRF52832 SOC ) and HX711.( There is an accelerometer...
Hi. I have a question regaring the nRF52833. I want to program the MCU using ArduinoIDE and I'm not sure if I have to use a programmer to program the nRF52833 and if so do...
SDK 15.3
SD S340
Bootloader implemented to update over GSM and BLE. BLE update code is taken from example secure_bootloader_dfu*. GSM update code is custom made. SDK is...
I set up nrf52832 that it is called proxy device, i create a loop that proxy device will sent 20 message to app phone (Android) within 100ms. But my app (Android) receive...
So I'm not sure that this is an error, but it is a little annoying. I have an application that sends sensor data using ble_nus. Works great, except that mixed in with my data...
To the kind attention of Nordic support team,
In case of a device and host ble bonded, I'm giving a look at disconnection reasons codes due to (1) host entering sleeping...
I have build a project, and it has been running normally. Now, I want to test a font data, so I created a function. But strangely, although the compilation has been successful...
