Problem Description
The custom hardware board cannot boot normally after flashing the firmware. However, the exact same firmware image works perfectly on the official nRF54L15...
Hello, I am raising this issue because I am working with multiple devices doing CS procedures between each other and I found a limitation. I am working with NCS 3.3.1. When...
For my project I want MCUboot with the upgrade image placed in the external flash, and TF-M. I am not able to get this combo to boot however, and I suspect the reason is that...
Hi!
I am trying to do a DFU with external flash, using a nRF54L15-DK development kit.
To evaluate this feature, I use the l9_e3_sol example available on GitHub (I use...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
we use nrf54L15 in the BLE+ UWB design, we checked that the nRF54 series support ToF, Can an external active crystal oscillator be added to provide a stable system clock and...
Hi, I'm experiencing flash write issues on an nRF54H20 DK's on-board NOR flash. I'm using ncs and toolchain v3.3.0.
Setup: the on-board MX25UW6345G on EXMIF, using the jedec...
Hello.
I am testing saadc function.
When I was connect the saadc pin with ground level, the saadc value represents negative value.
So I am searching the similar problem...
Hi:
I'm coding with the nrf52840 dk sample.
as we know, the gatt operate is notify,read, write, etc.
I have found the event about the write,and notify:
case BLE_GATTS_EVT_WRITE...
<environment> Windows10 ncs v1.3.0 modem fw v1.2.0 DK 0.9.0
I made one-shot agps app by modifying gps sample app. The behavior is this.
- download SUPL data from supl...
Just bought 2 nrf52840 DK's both stopped working
Observation
Was able to program and run SDK examples.
Above working setup not disturbed,so all cables are in order...
Hi, I'm using nrf52 dk and struggling to get low power consumption using multi_sensor_freertos ZigBee example from nrf sdk. Can you provide me some guides on how to optimize...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52811
I want to detect power failure/low battery voltage using POF feature of nRF52811 chip. Here is the code I'm using:
...
I am trying to capture audio PDM samples at every 5s interval blocks, but at the time of "pevt->buffer_released" event when i am giving the new buffer to PDM driver it results...
Hello, I am working on the NRF9160DK card. I am using SDK 1.3.0 and the latest modem uploaded: www.nordicsemi.com/.../Download 2020-04-29.
Whether it's with the asset_tracker...
Im following the guidance to upload modem code and application code, downloaded from project page, onto the Thingy:91.
Current state, after following guidance, is: I hold...
Hello,
Currently I have implemented a UART callback using the CONFIG_UART_ASYNC_API setting as follows:
However, all data that I receive is appended constantly, until...
Hi, I want to measure the data transfer speed of BLE. I use the nRF52840 DK with the ble_app_uart example
I created a dummy string of 20 bytes (default length of one packet...
I have a shipping product with S132 2.0.1 with multiple problems with the LFRC clock.
There are seemingly at least 4 errata that apply (77, 132, 146, 192).
Are there...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
my project is to send pressure data from one device to four other devices, it is medical field, previously i worked in nordic openthread udp protocol using nrf52840 for mesh...
