I am unable to perform a fota on an nrf9160 based device in the field since my nrfcloud account was updated to require the use of the new memfault based version. There was...
Hi,
I just read the nrf54l15 errata [100] of the nrf54l15. It's actually a huge issue, as we do have an interrupt line on one of the affected pins, that is active low, eg...
Hello, We're in EMC testing for a host product built on the nRF9151 (LACA A1A, FCC ID 2ANPO00NRF9151), running modem firmware mfw_nrf9151-ntn 1.0.1.
For our lab build, we...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
We are using the nRF54L15 chip in a new product that is essentially a sniffer. We periodically turn the receiver on for 5 to 10 seconds to sniff for BLE advertisements from...
Hi. After I modified the function static void ranging_data_cb(struct bt_conn *conn, uint16_t ranging_counter, int err), I exported the IQ data, as shown in the figure below...
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
I am working with the nRF52840 DK and was looking for a way to set a compare register to trigger at 300 ticks, and another to trigger at 40000 ticks. The register that triggers...
Hi,
I am a new comer so perhaps I made a mistake during project configuration.
I am using nrf Connect v3.4.2 on Windows.
I trie to add CC310 libray in sample hello_world...
The detected device could not be recognized as neither JLink nor BLE could be captured in wireshark, nor could the nRF Connect v3.4.2 - Programmer produce "Unsupported device...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both BLE scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi. This is my first experience using Nordic Products and I have run into some issues trying to "Open nRF Connect Studio Project" from SEGGER Embedded Studio. I want to run...
Hi
I'm trying to load the sample project Mesh light using SDK 1.3.0 but cannot load the configuration file properly. Im using a nrf52840DK
I have tried to update requirements...
Hello,
I wanna create a central/peripheral device. This device must be connected to mobile phone as peripheral. Also, it must be scan peripheral device's advertisement and...
In order to implement the event callback mechanism, the Observer Pattern is implemented by "Flash Section". This idea is novel, But what are the advantages of this method...
Hi everyone,
I try to write using I2C but I fail and I cannot figure out the issue
This is my code snippet.
When I run it it returns the following error
It fails...
Hi everyone,
I am looking the TWI examples and I am confused regarding the nrf_drv_twi_tx and nrf_drv_twi_rx . What I've understand so far is that the nrf_drv_twi_tx function...
Hi,
We are developing the project based on nRF52840 chipset. We are configuring the chip for mesh application and using generic on/off model to send the data on the mesh...
Hello ,
There is two kind of clock source as i can see from the sdk files;
one of them is cpu that is ok but for the first one i couldn't figure out it's source "NRF_SYSTICK_CSR_CLKSOURCE_REF...
Hi all,
I've got some code running on my nRF9160dk that is behaving oddly. LED 3 blinks as expected (2 seconds on, 1 second off) but GPIO 10 (pin 18/ULTRASONIC_TRIG) remains...
