Hi,
We are unable to get the correct location (even approximate) using the nrfCloud API for Location based on Single-Cell. For the given "mcc", "mnc", "tac" and "eci" combination...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hi,
Does the nRF54L15 support Direction Finding (AoA/AoD) and Channel Sounding together — i.e., can both features run on this specific chip, either simultaneously or at...
Hi,
We use the nRF9151 modem and need the following data from it: Mobile Country Code (MCC), Mobile Network Code (MNC), Tracking Area Code (TAC), cell_id and rsrp.
We...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
I've got an application that reads MP3 files from an SD card, decodes them and outputs audio data to a codec via I2S. The codec is clocked by MCLK generated by the nRF. The...
hi Support Team
I am using 3 Development Kit flashed with Mesh Beaconing Example kept apart distance of 30mtr , Say A, B , C
In Another Kit I flashed ble_app_beacon Say...
Does `sd_ble_gatts_hvx()` queue indications and if so then when does the next message get sent; after the previous one is sent or after the receiver acks the previous one...
Hi
I have a project that uses several protocols, including UART and USB CLI
As such, I had to move the nRF logger to work on RTT, so that everything could work properly...
Hello,
I was wondering if it is possible to read the model (e.g. NRF52810_xxAA_REV1) from a chip with nrfjprog?
In production we use nrfjprog to program our devices and...
Platform: pca10100
SDK version: SDK17.0
Purpose: Use radio to scan Bluetooth devices and perform CTE sampling. When the scan data and IQ data accumulate nearly 4K, output...
I'm using a 52840 and need both low stand by current and use of a UART. I understand that the UART drives up the power so I'm trying to completely shut it down when not being...
Hi, everyone
I am studying openthread.
I had a nrf52840 Dongle(running CLI/MTD example) act as MTD node to join in the openthread network.
The Dongle's LEDS were removed...
Hello,
I am using a nRF DK (nRF52832 - PCA10040 - SDK 15) to communicate with a custom electronic device developed by my own company (which integrates an 1-Wire slave)....
Hello,
I have a question regarding eDRX mode on the nrf9160 in combination with NB-IoT. I tried to configure an eDRX cycle of 20.48s for the use in a battery powered actor...
Hello,
I am using the nRF52832 on a custom board, with SDK 15.2 and SD132 v6.1. My BLE application uses the SAADC to measure VCC voltage every 6 hours. I am using an app...
Hello Sir,
I am Working with nRF52 DK Development board. My application based on BLE. I want BLE stack for Scanning mode and also tell m,e how to operate with mobile apk...
How to
1. increase advertising frequency - Which BLE GAP parameter should be updated?
2. increase RSSI signal strength - My device is not battery operated, so there are...
Hi,
How can I make the modem start a hot fix after rebooting the nrf9160?
I am getting a GPS fix, then powering down the modem with CFUN=0, which should be saving the...
Hello, I recently bought a nRF52840 with the intention of using it as a substitute for UART wired communication. What I want to do is send and receive messages between my...
