I'm trying to transmit audio data between two nRF5340DKs. These boards share timestamp information via the wireless time synchronization method here: https://github.com/nordic...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hi guys,
For a client of mine I'm working on an openthread RCP implementation using a SolidRun N8 that contains the NRF52833.
I'm using ncs v2.9.0-nRF54H20-1.
The problem...
I’m working on high-throughput data transmission using the nRF5340. My target is 80–100 kbps. However, I’m encountering issues on some phones during the transmission. The...
I recently bought 4 PCA10040, out of those, two are basically bricks, because somehow the app protect is enabled and all ways I found on this forum to recover do not work...
I wanted to know if this program starts sending advertisements using the Coded PHY OR if it starts advertising in the normal advertising channels using the normal 1Meg output...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
When mesh_config_clear() is called with a setup containing a file strategy MESH_CONFIG_STRATEGY_ON_POWER_DOWN and an entry in that file has been changed but not yet written...
Hi
I am working on Mesh using light switch example,
1. Wants to relay the ON/OFF message to other server.
2. And send mesh message from server to all node in mesh network...
Hello,
I have program w/o using softdevice to drive an LED driver using I2C. I was able to get this to work very well with out a softdevice, however once I loaded a soft...
Based on nRF5_SDK_15.3.0_59ac345 for nRF52810 application,
a. With s112_nrf52_6.1.1_softdevice.hex and app.hex, it works normally b. Add bootloader, fds_init function will...
On custom nRF51422 hardware with S110, I eventually found that after 3 minutes the advertising timeout turns off the system.
I reproduced it by using the nRF SDK v9 project...
Hello Nordic Support!
I will ask you a question.
Soon it will be mass production from prototype development. I built with MDK-ARM and wrote code with J-LINK +...
in my circuit, it takes 17ms for VCC_NRF to go up from 0 to 1.7V and reach 3.0V, but nRESET PIN does NOT to go up to VCC_NRF.
what is the potential cause of this problem...
Hi all,
I'm working with a chip that is not really i2c compliant and requires us to not send a STOP at the end of an i2c read/write (I know super crappy but that's all I...
Hi to all, i am developing an app with nrf52840 and i want to use cc310 backend to generate ecc public/private key pair. after adding some files and enabling cc310 backend...
Hello,
I am using a development board pro nrf52840 mini from Sparkfun.
I'm trying to use the TWI peripheral on nrf52840 to communicate with an external device (another...
Hello! I'm using nRF5_SDK_15.0.0_a53641a to programm my Nordic NRF52832 with Segger Embedded Studio. I'm trying to increase the BLE Tx power to 4dBm. At the moment I've tried...
1.How do I use TWI \ TWIM Read\Write in blocking mode ?
I am facing an issues with my nrf52840 based design, where I issue consecutive TWI write\read .
I am monitoring...
Hi,
Why can I no longer access firmware.nrfcloud.com as, e.g., still described in readme.rst for the http_application_update sample. I have seen that the "regular" nrfcloud...
Hello ...
New to Nordic SDK and trying to implement SAADC to read battery level. Have looked at a bunch of posts. I started with the ble_app_uart example app and tried to...
