Hello,
I attempted to rebuild the reference circuitry from the nPM2100, and I am measuring unusual power consumption using the PK2 outputting 1000mV.
Partially, I...
Hello,
I am currently working with nRF52832 and have been referencing the following sample code: nrf52-esb-ccm-example / ptx/main.c
I have successfully implemented AES...
Hi,
I am working on integrating the peripheral_uart sample with nRF5340 Audio (LE Audio) on the nRF5340 Audio DK.
Setup
Peripheral Side
Merged applications:
peripheral_uart...
I am interfacing a TLV320AIC3204 codec EVM with an nRF54L15 board using I2S.
The codec EVM default configuration is working correctly. I verified audio on the EVM side....
Hi Team,
Facing below issue related to MPSL.
** Booting nRF Connect SDK v3.3.0-ba167d9f3db4 *** *** Using Zephyr OS v4.3.99-fd9204a02d52 *** [00:02:14.519,667] <inf> app...
Dear Everyone, We're using the PAN B611 evaluation board (ENW89861AXKF) which features a PAN B611-1C Bluetooth Low Energy (LE) module which is based on the Nordic Semiconductor...
Hi Nordic team,
We are designing a custom board using an nRF54L15 together with an nRF7002 WLCSP.
Our board has a single 3.3 V power rail. We would like to confirm the...
I am trying to connect the MS5611 ( https://www.te.com/usa-en/product-CAT-BLPS0036.html ) using the GY-63 Sensor Module to the n RF52840 with the nRF5_SDK_15.3.0_59ac345 SDK...
Hello.
I would like to know which PCB surface finish would be used for bluetooth application. There are HASL, OSP and ENIG. nRF51822 IC chip and PCB trace antenna will...
Hello All,
We are designing a Tracking device system, for this we use nRF9160 LTE+GPS combo module. this system is battery operated so we need to monitor the battery continuously...
Hi,
I've been trying to lower the power consumption of the MQTT example and followed the guide in here .
1. I compiled the low power UDP example and do exactly all the...
My nRF52832 firmware application transmits data to iPad which converts it into a flowing waveform. The waveform flowed smoothly when SDK13.1 was used. I migrated the firmware...
Hi. I use 15.3.0 SDK and Segger studio.
I test Ant communication
I have a question.
ant_bsc_rx example of Ant plus, there are 2 handler.
ant_bsc_evt_handler is set...
Hi guys,
I’ve got a simple nrf51822 board which does not have any GPIO used - the system is a beacon doing its own advertisement without any intervention. The board schematic...
I am getting started with the NRF51 DK. A previous post suggested that " you should start with the precompiled versions of the examples that include the SD. These always work...
Hi.
I'm useing SDK 15.3 for testing DFU in nRF52832. I've already porting DFU to project ble_app_uart_c. now, I want to run BOOT project,and I'm useing project secure_bootloader...
Hi,
I understand there have been a few changes in the nRF Connect SDK with regards to Secure Boot and SPM.
I've been stuck for many hours trying to understand why I'm...
Hello,
I'm facing an issue when i want to delete some file in my FDS file system. Indeed, sometime, i can find dupplicated file with the same file id and the same record...
hi ,
i just realized that i damaged my NRF52 dev kit debugger chip. it is heating up and not working . the rest of the circuit including NRF52832 are fine. is there any...
I am using sparkfun nrf52832 breakout. I am new to this. I don't have a JTAG programmer so I cant program with keil. Is there an alternative solution for the software used...
I was using Sparkfun nRF52832 board to test my application, programming it with FTDI over Arduino IDE. Now I made my own PCB and found out that the IC doesn't have bootloader...
HI there! I am currently having some issues trying to add a custom 16 bit service to my nrf51822 project. Basically I am trying to make a dummy peripheral that I need for...
