I got a 52840-DK a couple of days ago. I installed the latest IAR Embedded Workbench (9.70.1); also downloaded the latest Nordic SDK,and then started building and executing...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
I've got a custom board fitted with an nRF52832. Am running NCS v2.6.0. Operation involves:
1. Being in System On idle with all peripherals disabled to keep current to a...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Hi all,
I am using power profiler kit to measure as mentioned below screenshot.
I want to achieve current number as mentioned in Nordic product specification as" IOFF_RAMOFF_RESET...
Hi,
I'm using nRF52832 with IAR and SDK V15, S132.
I incorporated the peer manager in the uart serial profile example.
I assume, since I have 3 pages (inc. GC) set in...
I have a device that uses peer manager to pair using a key. I have noticed that the device will connect to an app and stay connected even if the pairing procedure is not completed...
Hello,
I am using the nRF51 dongle, SDK v10 and s310.
I want to use the dongle as a ANT+ receiver and BLE client to connect to multiple BLE peripherals. I have looked...
I am once again frustrated with nRF5 API's. Getting a value from analog input pin is that simple with Arduino API's:
int sensorValue = analogRead(A0);
That's all you...
I'm using an IMU sensor and transferring data over Bluetooth to Android device. The data sampling at 400hz, and I'm sending 6 packets per connection, each packet 20bytes....
Hello!
I am using the PORT event interupt sense handler to wake up the device from various pin interupts. We have in total 6 pins that need to do that.
This works fine...
Hi,
In my project, I am interfacing various modules (UART over ble, ADC, SPI, I2C) on nRF52840-Preview-DK board. I use IAR Embedded Workbench with nRF5_SDK_15.2 for code...
Need assistance/recommendations for working with smaller pin pitch (150 micron) mounting holes for the new nRF52480 chipset. Our current contract manufacturing supplier for...
Hello I noticed the problem with nRF51 DK and ble_uart app.
1. The nRF51 DK is connected to the Terminal
2. Connect to the nRF via "nRF Connect" application on Android...
Hello:
I read the documentation and errata for Rev 1 of the nrf52. I am using the Rigado BMD300 module (thus the nrf52) without a softdevice attempting to do on the fly...
Hi All,
Currently i am working on nrf51822 chip, For that i have downloaded nRF5_SDK_15.0.0_a53641a.
Now, i am trying to execute mouse hid example in nrf51822 chip, but...
Hello, it seems that the 15.2 infocenter radio_test instructions are somewhat different from the 15.0 infocenter instructions . Trying to get a general understanding of how...
Hi there,
I was hoping you guys could point me in the right direction with regards to the use of the nrf_mesh_disable() & nrf_mesh_enable() functions. Since the "friend...
I migrated my nRF52840 project to nRF5 SDK for Thread and Zigbee 2.0.0 (from 1.0.0), but I keep getting a linker error:
Building ‘myproject’ from solution ‘myproject’ in...
