Hi, Our nRF52840 (NCS v3.4.1, SoftDevice Controller) is a central that connects to smartphones running our app (phone advertises, nRF52840 initiates). About 12% of connections...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
Hi,
I have a MBN5283DK from murata, and I am trying to program the simple blinky example on it. The thing is, using nRFgo studio, I programmed the hex file onto the board...
Hello, I am working on detecting extended advertisements on the nRF52840, with the extended advertisements coming from a Google Pixel 2 phone.
I am basing my program on...
I am receiving data from a phone, i want to send back a word .
So , this is probably wrong but , to send :
void sendBluetoothData( uint8_t data[], uint16_t length)
...
I am a novice who now deals with nrf52 dk.
I installed command line tools according to the guide in the link above. I have installed several jlink programs, of which I do...
Hi,
I enter problem when I tried to delete bonded data from my example code using pm_peers_delete()
SW: nRF5_SDK_15.2.0_9412b96
HW: PCA10056
example: ble_app_hrs_freertos...
nRF9160 DK: I followed the userguide , devzone.nordicsemi.com/.../getting-started-with-nrf9160-dk
I done with 2 examples: AT Client and Asset Tracker examples. I passed...
Hi,
I am developing against a custom board built around the NRF52840. I am trying to store and retrieve values from flash using the fds module. I am not seeing any errors...
Hi, I am going to use the nRF91 DK to program an external PCB with the nRF9160 on it. The DK documentation says that only 1.8V or 3.0V is supported for external debug/programming...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
Dear,
I am using nRF9160 DK,
firmware: secure_boot & AT_client
and Tale_SIM from Telia, I want to get the current GPS position by AT command?
Is it possible? Which...
