Hey everyone! I'm working on my Master's thesis about Rust in embedded systems and trying to figure out how much Nordic Semiconductor actually backs the Rust community.
...
Hello,
I'm using the nRF52840 DK and I have a TensorFlow Lite model (.tflite) larger than 1 MB. Is it possible to load this model from external flash memory instead of internal...
Hello,
I am developing a product using the nRF54L15 and have noticed a discrepancy in the documentation regarding clock pins. My intention is to use pins 1.02 (SDA) & 1...
We're developing a low-power application on the nRF9160 where we need the device to stay connected to the server over LTE, so we cannot enter System OFF mode. Instead, we...
Hello,
I'm evaluating the nPM1300 for a battery powered project. What is the quiescent current of the LDO? And is there an output current vs dropout chart?
Thanks
Hello,
I study the UART Central-Peripheral example (NUS) out of the box based on Visual Code IDE. I would like to understand on the Central part:
Where exactly in code...
I am facing an issue while trying to flash code onto a custom board based on the nRF52832 . I used a sample iBeacon project for testing. I created a custom board configuration...
I'm attempting to change phy in a program based on the UART example and am following the same process used in the att_mtu_throughput for changing PHY.
Calling sd_ble_gap_phy_request...
Hi,
I'm using nrf52 + SDK11 + softdevice 132 2.0 and trying to integrate
the OTA dual bank bootloader. Using the nrfjprog tool I program the
softdevice + bootloader....
I am using the nrf52832 soc, and have a requirement to run the device in low power mode and using the timer with a timeout value in days? how can I do so?
Sample code would...
I want to read data, advertised by a bluetooth beacon.
I have made this work before with SDK v14 using NRF_SDH_BLE_OBSERVER() to register a handler function to handle BLE_GAP_EVT_ADV_REPORT...
As a complete newbie to this a bit of guidance would be really helpful to point me in the right direction.
I want to create a simple device with a couple of switches (physical...
Hi Nordic community,
I'm sending several packets from nrf51822 (custom board) to Android application. At the moment I want to configure the sensor by sending commands from...
hi,
I tried to recover custom nrf52 board by nrfGo stuidio,and it failed,the logs as below:
------------------------------------------------------------------------...
Hi All,
I'm using a sdk11 and i have started using the glucose profile example to use a peer_Manager.
I have modified it to have a just work behavior. It works correctly...
We have a potential application where we have to send data over BLE at 3kbps and store in external flash memory at 8kbps. The last memory accessed in external flash memory...
I have a NRF52840 and wanted to know, how much of a signal gets into another channel in BLE.
I am going to explain what I mean so there is no confusion :).
The Bluetooth...
Hi,
When I migrated the nRF51 project to nRF52, I got 67 L6218E errors.
I am not sure how to solve that kind of errors because I already added the related .c file to group...
I need to use an external RF amplifier. This needs two control lines, one for TX and one for RX.
I need some way to know when to change the state of the control lines. Is...
I'm noticing some irregularity on the SCL line coming from my Nordic 52832. I've attached a Saleae logic trace here. What are the potential causes for this type of behavior...
Hi,
I'm facing issue in the range of communication between the 2 NRF24L01+ modules(1452AB). My design is to interface the NRF24L01+ with more than 6 modules with one HUB...
Hi,
We are testing with the experimental_writable_ndef_msg example from SDK12.2.0 and we have issues reading the nordic NRF52 Hardware using the PC-Card Reader identive uTrust3700F...
