While we understand that the RRAMC controller on the nRF54L15 performs writes to RRAM using full wordlines, the datasheet indicates that the nRF54L15 RRAMC supports writes...
Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
SDK13, S132
Project stopped after start. I use standart initialization:
static void peer_manager_init(void)
{
ble_gap_sec_params_t sec_param;
ret_code_t err_code;...
I've connected some sensors using I2C and SPI to a DK and their power consumption is not being reflected in the PPK. Without any BLE acitivity, the current is almost zero...
Hi,
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux-x86_64.tar
I can capture the...
Hi,
I use SES import my keil project, and my keel project work well. With SES, i meed a problem, that is , i have a global variable like this:
uint32_t g_ulMainLoopCounter...
Nordic51822 no external 32.768 k of crystals in the routine what configuration
Use this routine
nordic\nRF5_SDK_12.2.0_f012efa-3d\examples\ble_peripheral\ble_app_bps\pca10028...
When I am stepping through my application code crashing at
memset(&cccd_md, 0, sizeof(cccd_md));
"Setup information:
IDE: Using IAR
Device: nRF52832
Soft...
I'm using the NRF51822 for a project that will be powered by a lithium battery. I'm wondering if it would be safe to use a diode ( such at this one ) to drop the 4.2V LiPo...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
For BLE, there is always an ACK in link level no matter it's write/read/notify/indicate.
How about 2.4G proprietary mode? Is it possible to just send a data without...
Hello,
I am using the nrf52832 with SDK v12.3 and PCA10040. Not using any soft devices, nor the RTC. The program is intended such that timer0 is set to toggle a pin (P0_11...
Hi,
We are working on Automotive project using nrf51824. below are some queries ,
We are basically want to use the chip as a Bluetooth to Kline(using Uart) bridge ....
Hi,
we would like to start a new product (update a design) and add Apple Homekit feature because ""Apple will now allow any registered developer to start building a HomeKit...
As i am new in embedded programming,I was trying to connect MPU 9250 with nRF52 DK by using given examples. now it is showing error
#error "No MPU defined. Please define...
