Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I am having trouble with buttonless DFU on my application. I am working on custom hardware on the nRF51822, SDK10.0.0, S130.
When I enter DFU from my application...
I'm working with pca10028.
Then gpiote interrupt is triggered twice.
Why is this happening?
And what is BUTTONx_EXT connected to PCAL6408A(U7) in schematics?
Hi,
I am new to nordic development. I have programmed segger program softdevice by s110_nrf51_8.0.0_softdevice.hex and program bootloader by dfu_dual_bank_ble_s110_pca10028...
My project is to communicate with the AD7780 via SPI.
Nrf is the master and AD7780 is slave. I am know implementing my solution referring to an example i found about SPI...
I'm trying to make the nRF51422xxAC advertise. Using Segger Embedded Studio.
I have this code: bpaste.net/.../f29f74986c10
On line 109, I have a breakpoint. At that...
I've followed the tutorial about setting the eclipse environement devzone.nordicsemi.com/.../
I've got every thing to work except the debugging, it stops every time at ...
Hello,
I am trying to set the nRF52 to power off and wake up on a momentary button push (scope measures momentary push logic low around 50ms-100ms). However, I am struggling...
This is from the previous Blog: devzone.nordicsemi.com/.../
I've looked at the other dev boards. I found this one nRF52832 System on Chip and Amber SPP-over-BLE profile...
Hi,
I'm using the nrf52832 Nfc and I can't set a variable nfc message, the nfc message must be constant... In my case I'm trying to send a text via BLE and put it on the...
I found lots of macros in Makefile like below,but I did not found they were used in C or assemble file. I am cleanup my Makefile to remove unused macros... so could I remove...
I'm using a 51422 for a very short range, fixed system. I will never need the chip to receive or be received from more than 5 meters away, and more often just 2-3 meters....
Hi,
I own a Redbearlab BLE Nano with a nrf51822.
I want to use it to drive some WS2812 rgb LED (neopixels), using precised timings for bit-banging.
Before driving...
Hello everyone,
I am having difficulties on changing the advertising name of my device (nRF52832).
Here is the piece of code that I am using to do it:
ble_gap_conn_sec_mode_t...
hello.
How can the hidden setting of BLE be realized?
For example, (as log of nRF Connect) as follows:
ptlog1.txt
thanks.
I will attach a screenshot of NRF connect...