Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi All,
I need to certificate the nrf52 to Fcc. I understood that the radio test is very useful.
I try to clarify what the code permit to do, because i want to adapt it...
I must create an application for nrf5 dk with s132 v3.0.0 sd. In this application a device must implement heart rate service client, while continously trasmitting a reference...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
Hi
I am presently working on MPU92/65 sensor interfacing with TWI/I2C.
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v12.2.0 and keil...
using
nrfjprog --rbp all
and got a success
and using
nrfjprog --readuicr
got unavaible
but if using j-flash and read whole chip, it's able to be readback...
it...
I am trying to figure out how/if I can program the softdevice hex from keil? I know I can just use nRF studio however its annoying sometimes....I also noticed I cannot rebuild...
I'm using an nrf52dk (pca10040) to develop an mqtt subscriber application.
I'm using the IoT softdevice, with the IoT 0.9.0 sdk example for subscriber as a starting point...
Hi,
I want to know in general about the UUID that we add in to GATT files.
Basically, I want to know that there are different UUIDs for different applications heart...
Hello everyone,
I successfully implemented the static key to access a characteristic now I want the user to udpate the passkey through another characteristic (which is also...
Hello, with a little research, I now decided that this is the general but incomplete (which is why I'm asking the question) step :
Immediately look up SP register, if the...
Hello,
we developed a custom board using the nRF52832. We are having problems communicating with the mma8652fc accelerometer using I2C. We also have a Rigado BMD-200 EVAL...
Problem : After successful compilation of ble_proximity example in SDK 12 version
Ble is not showing up in Android device
How ever If I load pre compile file in example...
What is the difference between the GAP Device Name and the Complete Local Name in an advertising or scan response packet? Can the two be different?
We have a requirement...
Is it possible to support both LE Secure Connections Just Works pairing and Legacy Just Works pairing in a single device?
My concern at the moment is that if I require...