Hello, when flashing t device using nrf connect icon, it fails to flash with following message
After investigation I found the generated_nrfutil_batch.json (autogenerated...
Vidar Berg appears to be off today. I hope he's okay. Could someone please pick up Case ID: 360532? We only get about 4 hours of overlap per day due to difference in time...
Hello,
I've been working on a feature lately that involves writing the OTP registers in UICR on nrf54L15; after writing the registers I also wrote the protected value (0x50FA50FA...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
We are using a BM833 chip on out PCB. There, we may or may not (config-dependant) interact with a sensor via I2C. We observed (statistically), that using the I2C communication...
Platform: nRF54LM20A SDK Version: nRF Connect SDK v3.3.1 MCUboot Version: Included in NCS v3.3.1
Background
On the nRF54H20 , the IronSide Secure Enclave provides a...
Hi,
I’m reviewing the release notes of the Zigbee R23 add‑on , and I see that the compatibility table maps each add‑on version to a specific NCS (nRF Connect SDK) version...
Hi there. I'm attempting to do trilateration between 3 nRF Devices. A1, A2, and A3.
A1 - A2 I can get using the nRF Distance Measurement toolbox
A1 - A3 I can get using...
We have implemented a simple contact switch using the nrf52840 and the latest zip generator (v99). The device connects to a Samsung Smart things edge router. A contact device...
Hello Nordic Team,
HW: nRF52840DK
SDK: ncs v2.8.0
App: hci_pwr_ctrl
I am testing with hci_pwr_ctrl example to see how tx power can be set from application.
The...
I am working my way through the Beginner course on Dev Academy, and am trying my hand at using my own accelerometer breakout board communicating over I2C for lesson 6.
I...
Hi,
I have used course's example for GPIO interrupt for toggling LED and used to update BLE adv parameters without using DK buttons library. But, as soon as, I update BLE...
Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
Hi All
Hi, I am using nrf51822 controller in my design for with SMD chip antenna for RF output.
Can anyone suggest me any reference design(Hardware and Layout files) to...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
Hi,
"In a BLE Mesh network, if a client uses GAP attributes to send data, can it also use the GATT profile to communicate with a single device? For example, can the client...
I am currently using SDK 17.1.0 to implement dual UART mode on the nRF52833. UART0 is used for logging, and it directly utilizes the SDK library without any modifications...
I use SDK v.2.6.1. To avoid other possible factors affecting the results, I only keep the simplest function in the code which is reading the potential of gpio every second...
In the pairing process among 1 Central and 2 Peripherals
Sometimes the Pairing processing rarely does not work correctly and the following log output:
<err> cis_gateway...
Hello,
We would like to inquire about a technical issue regarding the nRF7002 + nrf5340 with sdk v2.7.0. We have a nrf7002 module connected with nrf5340 through qspi interface...
