Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi folks,
I'm attempting to program an nRF52833 using a Segger J-Link+ connected to the SWD program/debug pins on the board.The board is only an nRF52833 - as a learning...
hi, noted a few things in the Rev 1 Errata v0.8 that might be tricky to solve practically in sw/hw
3.16 [33] RADIO: GPIOs can exhibit radiated emissions
max...
I'm currently attempting to register a service and it's subsequent characteristics statically using variables and not hard coded GATT tabel , I can successfully register an...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Dear,
We have project using normal advertisement (not extended) on a nrf5340 module (Raytac MDBT53-1M) to send data using Manufacturer data.
We have a product already...
Hi, Currently Im developing on a custom board that has a NRF52840 and a NRF9160. Both MCUs communicate using UART Async API and I added the support for LPUART on both sides...
Dear Nordic Team, we are using the adafruit_feather_nrf52840 and nrf52840dk for our prototypes and recently the toolchain around nrf and zephyr has become a problem. Build...
Hello, I have two nRF35340 DK. One of them can be flash successfully, another one always encounter this issue:
I have tried
nrfjprog --recover -f NRF53 --coprocessor...
Hello,
I'm starting to use the PPK2 to understand the current consumption of various IOT products. I have a question about what happens in amp mode should a dead short fault...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. However, this PR has been applied. I connected one smartphone app and two boards(nRF5340DK) to the mesh...
Hello everyone,
I am developing a project where I need to perform bluetooth OOB pairing using an NFC reader. I have a couple questions about this.
The first is, what options...
Hello,
I am using the "peripheral_nfc_pairing" example to pair my nRF52832 in the ANNA-B112 module with my iPhone XR. Currently, the example does not work with my iPhone...
Hi Nordic-Dev's,
I've a short question. Is there a native build of your nRF Connect for Desktop Tools for Linux aarch64 (Ubuntu 22.04 LTS ARM) architecture? I want to separate...
I've previously successfully performed OTA DFUs of our application (basically a heavily customized peripheral_uart), running on hardware substantially similar to the nRF5340...
