I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Dear Nordic support team,
What is the maximum number of timers that I can create (and use) using the app_timer lib?
err_code = app_timer_create(&m_timer_m_1_0,
APP_TIMER_MODE_REPEATED...
I've recently started sharing development activities with another developer. I created a GIT from the folder: C:\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\ble\myProjectFolder...
I'm leveraging off the heart rate sensor example to create my own VS service. I've successfully registered a 128-bit UUID with the Soft Device which is enumerated along with...
Hi,
i get the example for using PWM to run and modfied it to use it in my application. My Prolem is that i only have one PWM Output toggle Pin. How can i build a second...
Hi,
I'm using the MCP to send a long to a nrf6310 board loaded with SD v6. The board hangs when I send a long though, is this due to the MCP not being set up to send longs...
Hello,
I have the nRF51822 Evaluation Kit. I have run the basic code examples like 'Blinky' and the BlueTooth HRS (Heart Rate) application, successfully.
Now I would like...
Hi,
Is it possible to give a function address to the "Task End-Point" of a PPI channel?
Like :
err_code = sd_ppi_channel_assign(PPI_CHAN0_TO_TOGGLE_LED,
&(NRF_TIMER1...
I am designing a device that needs to operate both as a Peripheral (such as a Heart Rate sensor) and also as a Central so it can optionally connect and gather data from other...
Hi,
in my application I have a device that has to be controlled by a remote control. For transmitting data between the remote and the device I would like to use BLE (not...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
