Excuse me.
When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
Hi
nRF54L15-DK QFAAC0, ncs v3.4.0, project path: ncs\v3.4.0\zephyr\samples\boards\nordic\system_off
After compiling and flashing this example, the power-on reset (POR...
I have the matter light switch sample, SDK 3.4.0, on the nRF52840 Dev Kit. I can bind it with a light using Home Assistant (Ikea light) and it works OK. However after a while...
Hello team,
I have the issue in some samples of nrf5340, after I successful erase and flash, the controller seem to be stuck at bootloader.
I observed the below image...
Dear Nordic-Support,
we are facing an issue with a nRF54LS05b and NCS v3.3.0:
The setup is a peripheral based on the nRF54LS05b and two centrals e.g iOS Phones A and B...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Excuse me.
When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
I am using ncs v3.3.0, and since Partition Manager will be deprecated, I followed the migration guide to use DTS board configuration. I am using mcuboot in firmware loader...
The NTN AT command guide documents a "Signal quality check" option for performing a pre-check before attempting to re-attach to the Skylo network:
https://docs.nordicsemi...
