Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
The swap algorithm is executed every time the device is powered on, and the swap type is "perm". 0

Hello, We use nrf54l15dk + MX25R8035F external flash to do the matter development, and we meet some problems: 1. when the matter.ota is 1003KB, takes about 10min30s to...
16 views

0 replies

Started 1 hour ago
by Denghongyan
Not Answered
Error in Cellular IoT Fundamentals Course Lesson 3 Exercise 1 - Project will not build. Solution provided includes CONFIG_POSIX_API=y in prj.conf which is not mentioned in the tutorial. 0

I have followed the instructions in the DevAcademy Cellular IoT Fundamentals Lesson 3 Exercise 1 exactly, (whilist filling in the gaps from the cloned cell-fund repo) and...
44 views

0 replies

Started 4 hours ago
by dheadrick
Not Answered
How to determine that AWS FOTA has completed it's check, and found no update. 0

I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
23 views

0 replies

Started 7 hours ago
by Jstone40649
Not Answered
NRF52840: accidental back-powering by applying voltage to GPIO pin when power is off 0

Hi there, We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
33 views

0 replies

Started 8 hours ago
by Steve Van Kirk
Not Answered
Can't find services using ble_db_discovery_start() 0

Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140 I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
24 views

0 replies

Started 8 hours ago
by Randy Lee

Recent in Nordic blog

A presentation on how nRF51 DFU works

Hung Bui

Hi, I attached here some slides that we used in our technical seminar for Device Firmware Update. Download the presentation here: DFU_SDKv8.0_Pub.pdf The presentation covers: What DFU is and what…
- 4 Jun 2015
Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015
Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015

Latest guides

Software Development Kit: Setting up the Timeslot API

Hung Bui

Setting up the Timeslot API When you want to use the radio while still maintaining a BLE connection or have a task that you need to do uninterrupted by radio activity, you can set up a timeslot. The timeslot…
- 27 Jul 2015
Software Development Kit: Radio Notification

Øyvind Karlsen

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

Øyvind Karlsen

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
nRF5x: nRF51 series current consumption guide

Stefan Birnir Sverrisson

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

MartinBL

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015