Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
RF Section feedback 0

Hi, This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
15 views

0 replies

Started 1 hour ago
by Adam W
Not Answered
nRF5340 U-Blox Nora B120 FEM module 0

Hello, I have U-Blox Nora B120 dev boards. Nora B120 chip has built in Skyworks SKY66405-11 FEM IC and I want to use it. I read in the documentation to copy folder with...
- software
- nRF Connect SDK
- Evaluation
- antenna
- 2.4 ghz
- documentation
- configuration
- bluetooth le
- hardware
- nRF5340
14 views

0 replies

Started 1 hour ago
by .....
Not Answered
Selected CS on SPI Doesn't show up in device tree UI 0

I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
15 views

0 replies

Started 2 hours ago
by Tony
Not Answered
Security Level 4 Connection Failure in Central 0

Hello Nordic Team, I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
17 views

0 replies

Started 2 hours ago
by Yash48
Not Answered
ADC Values ofsett. 0

Hello, We have a sensor with 2 ADCs inputs meauring identical LMT70s on the board. With one of our older firmwares we get the accurate valudes of 22deg or so on both channels...
11 views

0 replies

Started 2 hours ago
by sawaiz

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Peripherals And RF Test: Writing device drivers for UART peripherals

Halvor Bjorstad

This post aims to cover some of the specifics of developing device drivers for UART peripherals for Zephyr.
- 20 Jul 2021
Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021