Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE/Wi-Fi co-existence on Thingy 91 X 0

Hi, The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
34 views

0 replies

Started 2 days ago
by Scott Grubb
Not Answered
No AT Response from SLM on BLG840F (nRF52840 + nRF9160) 0

Hardware: Fanstel BLG840F (nRF52840 + nRF9160, internally connected) Firmware Setup: nRF52840 running custom firmware using nrfx_uarte (TX/RX to SLM) nRF9160...
33 views

0 replies

Started 3 days ago
by Thanu
Not Answered
nRF54 + nRF7002 support 0

Hello, I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example). However, I am developing with nRF54 and I would like to understand if the combo nRF54...
39 views

0 replies

Started 3 days ago
by barbiz
Not Answered
BLE Mesh sdk 3.3.3 integration help 0

Dear Nordic Support Team, We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
34 views

0 replies

Started 3 days ago
by Kanhaiya Garg
Not Answered
How does partition_manager.cmake get invoked such that its mergehex call is always the last step? 0

NCS 2.9.1 NRF52840 Sysbuild but with only a single image (no bootloader) I've been trying to figure out how to change the merged.hex output and how to perform additional...
61 views

0 replies

Started 4 days ago
by Anthony Ambuehl

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021
Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021