Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
I NRF51822 respectively, as master and slave, and bindings need to pair between the master and slave. I do not understand the contents of this, who can provide these routines...
Hi Team,
What are the chances of pkt loss in case of concurrent observer, advertiser role using S130? Application is like in observer mode device need to observe some activities...
We have an nRFgo nRF24LE1 32-pin 5*5mm Development kit.
How do we program this as a stand alone application without nRFgo Starter Kit Motherboard ?
Is there any tool or...
Seeing the Log on wireshark for Central and peripheral communication after connection.
Here i am bit confused that when Connection update request is send by Slave after...
Hi, I try to access Generic Access to get device name.
So, I modified "ble_bas_c.c - ble_bas_c_init()" like this.
bas_uuid.type = BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME;...
Hi,
I want to find Bluetooth address of the Central Device which is running Master Control Panel Application....
but after succeful connection, each time I try to find...
I am using serial communication to have data from a sensor. That sensor only can support baud rate 115200 to communicate. Collecting data from that sensor I am trying to save...
Hello Everybody,
I have read these articles on the site : article_1 &
article_2
I need to do something like that, read around 8000 sample with sampling rate equals...
Hi,
I used the app of nordic , that puts the system off in order to measure the current at that mode.
the example i used is at this link . ( system-off-wakeup-on-gpio...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
