Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
The SDK 11 s13x migration document says:
The enumeration NRF_APP_PRIORITIES has been removed. Application developers must use the interrupt priority levels directly...
I NRF51822 respectively, as master and slave, and bindings need to pair between the master and slave. I do not understand the contents of this, who can provide these routines...
Hi Team,
What are the chances of pkt loss in case of concurrent observer, advertiser role using S130? Application is like in observer mode device need to observe some activities...
We have an nRFgo nRF24LE1 32-pin 5*5mm Development kit.
How do we program this as a stand alone application without nRFgo Starter Kit Motherboard ?
Is there any tool or...
Seeing the Log on wireshark for Central and peripheral communication after connection.
Here i am bit confused that when Connection update request is send by Slave after...
Hi, I try to access Generic Access to get device name.
So, I modified "ble_bas_c.c - ble_bas_c_init()" like this.
bas_uuid.type = BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME;...
Hi,
I want to find Bluetooth address of the Central Device which is running Master Control Panel Application....
but after succeful connection, each time I try to find...
I am using serial communication to have data from a sensor. That sensor only can support baud rate 115200 to communicate. Collecting data from that sensor I am trying to save...
Hello Everybody,
I have read these articles on the site : article_1 &
article_2
I need to do something like that, read around 8000 sample with sampling rate equals...
Hi,
I used the app of nordic , that puts the system off in order to measure the current at that mode.
the example i used is at this link . ( system-off-wakeup-on-gpio...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
