Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi all , when I run and debug my code , I frequently encounter error :
I think it's related RAM configuration on KeilC .
Please show me what is error ? And how to solve...
Hi there,
So I'm going through that complicated step of setting up the IDE for the first time to get started programming and I'm having issues doing it with the SES and...
hi everyone ,I want to ask you a question, I use the SDK12.3, when the device from the application transformation to the bootloader, when DFU is failed, why the deice is stays...
I am using nRF51822 (PTR5518A) with SDK v12 and s130 softdevice. To dump the code I am using nRF52 DK segger (PCA10036). With that I am able to dump the code but there is...
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
Is there any documentation as to how to connect a nrf52 chip (as found on the nRF52832 BT Module with Header Pins ( www.analoglamb.com/.../) or the nrf51 on the Adafruit bleFriend...
Hello,this is Lee.I have a problem about nRF51822.
When I turn on/off the power 2.8V to it ,it hangs up
frequently.I check POR function,I found that the residual
voltage...
hi,
i'm using the 32KHZ external crystal and i didn't find any free space in my PCB to put the crystal in the same side with the nrf chip, so the only solution that i found...
I am trying to implement a bootloader with rewrite protection on nrf52840 with SDK: 14.0.0.
But it seems that there is no flash write protection registers in nrf52840.
So...
UPDATE: Corrected language.
Hi,
While experimenting with BLE mesh networking using S130 on nRF51 devices and S132 on nRF52 devices, we have a problem with deafness while...
