I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi DevZone,
I am new to nRF SoC and SEGGER. After installing all tools, I can build and run examples.
I run into a problem to add and enable a nRF driver, like "UARTE...
Hello, I am trying to develop a rehabilitation exercise service using Thingy52.
Thingy52 is the only device to accomplish my objective which needs motion detection using...
Hi,
I have nrf52840 DK and PCA63511 Power Profiler.
I have two questions:
1. The Average Current Consumption measured with profiler is 110uA (18 mA max, over 10 s...
Hi,
I have Raspberry pi board which i want to use it as a gateway .on which server will get set up.
nrf52840 will be the beacons which i have already set up for sending...
I am trying to use the NRF connect mobile app on android 8.1.0 to try and connect to a Bluetooth server serving GATT request to verify functionality.
The server is running...
Hello,
I am using these pre certified modules https://www.nicerf.com/product_147_88.html in a project which is basically nrf24l01+ with a PA and LNA.
These support ...
Hi,
Just been testing the data rate of write without response commands, I'm only getting about 250 bytes / second which seems incredibly slow?
I've just got a simple little...
Hi,
Is it possible to route an analoge signal through a digital GPIO pin to access the inner analoge pins of a nRF52840? I want to avoid using via-in-pad to keep the cost...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
I have made changes from here in order to configure data rate at Coded PHY for mesh application.
Tested with two phones: Moto G5 Plus (Bluetooth 4.2) OnePlus 6 (Bluetooth...
Hi,
I am tring to display some information using NRF_LOG_HEXDUMP_DEBUG(). However, I can't see anything on the terminal. If I use NRF_LOG_INFO("xxxxx"), I can see the...
I'm using two nRF52840 DKs with SDK 16.0 with one as a central, the other as a peripheral. I'd like to setup an IRK whitelist on the peripheral. I've taken a look at the hid...
Hello,
I'm having trouble getting my program to compile with the SAADC. I started with a BLE template then added the battery service with sensorsim from ble_app_hrs and...
