Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Does the Bluetooth Peer Address of NRF51 Chips change randomly [every 15mins] or does it remain same?
When implementing whitelisting for secured connection, it is required...
Hi, I am unable to build this example in Keil Uvision5. I am getting following error:
"no source": Error: #5: cannot open source input file "......\main.c": No such file...
Hi,
I am trying to setup a testing environment using nrf51-ble-driver_win_0.5.0.
All of my job are:
Download nrf51-ble-driver_win_0.5.0, and program connectivity_115k2_with_s130_1...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
Hi,
Everyone,
I am using NRF51422 chip for my custom board. with transmission interval set to 2000ms and Tx power to -20 dBm, I transmit 32 Bytes BLE data and Scan and...
I use the softdevice which is s130.The code is from the demo:
static void nus_data_handler(ble_nus_t * p_nus, uint8_t * p_data, uint16_t length)
{
for (uint32_t i =...
Hi,
i'm using SPI to transfer data divided into packets of 24 bit from NRF51 to a DAC. The function that allows to send data is:
spi_master_send_recv(SPI_MASTER_1, data_vector_tx...
I'm having trouble starting my application after power cycling after flashing it with the DFU app.
I started nRFgo Studio. Erased the chip. Programmed the SoftDevice (s130_nrf51_2...
I was just wondering if anyone has any experience with or thoughs about using Zephyr ( www.zephyrproject.org/) or Mynewt ( http://mynewt.apache.org/) that they would like...
Hello all,
i am struggling with the example code of the Enhanced ShockBurst Protocoll in SDK 11. I cannot really see the structure of the code, to which time which event...
