I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I encountered an issue, please kindly refer to the attachment for the detail.
"'' The problem is: a> Run demo on PCA10056 (BLE adv & ANT continuous scan). b> ANT Dongle...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
Hi,
Greetings!
I want to disallow an unknown bluetooth device (like phone, etc) to connect to "secure_bootloader_ble_s132_pca10040" except from a bunch of pca10056 (central...
Again, I'm having trouble with the driver library. Earlier when testing I had SPI working OK as a small standalone test , but now I want to add SPIM to my actual application...
Hi,
two days ago I started checking the usbd_cdc_acm example in order to add usb serial comm functionality to my project. and I have some fundamental (newbie) questions...
Hi all,
I'm trying to add to our application BLE DFU feature. Therefore I'm testing first the secure bootloader example provided in the SDK v16.0.0
I managed to build...
Hi!
I have been using and loving the simplicity brought by the Toolchain Manager (TM).
But now I want to use an application available on the master (Connectivity Bridge...
In an attempt to add a custom UUID to your current project I change NRF_SDH_BLE_VS_UUID_COUNT from 0 to 1. Then loaded the code onto our PCA100040 53822 devkit. At runtime...
