Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I'm working on TWI with nrf52832 dev board, using examples from SDK 16. Here's the code:
I see no activity on the logic analyser and the application gets stuck in the...
Hello, Im working on project that communicate with gps/gprs and it works with the example/peripheral/libuarte. but when I want to integrat it (add) it to central peripheral...
Hello Support
I have an error when I try to add a custom CLI command with the API "otCliSetUserCommands()" . I added two commands for my example. The commands work fine...
Using the following:
Rigado BMD-360 nRF52811 development board.
Softdevice S140 7.0.1
SDK 16.0
Using two development boards inches apart, one development board sends...
I flashed two nrf52832 with a black magic probe. Unfortunately after reconnecting the USB, I wasn't able to flash them anymore. So, I tried the nrfjprog command line program...
Hello,
Our application is currently based on the Nordic SDK services such as app_scheduler and app_timer. It is not possible to change this to use an RTOS do to regulatory...
Hi Devzone:
I am trying to gauge the power consumption after nrf_power_system_off() is called.
So is there a list of the hardwares that "nrf_power_system_off()" shuts...
I am using nrf52832 radios to communicate using ESB without DPL. I have selective_auto_ack=true and I set the payload.noack=true. But each time I transmit and there is not...
I am trying to create a description of my peripherals in the device tree. For example, I want to describe the pins that will control the input type for the ADC. Current input...
Open LTE Link Monitor OK, but point connections appear with the following blank interface
Here's the LTE Link Monitor that shows the blank
LTE Link Monitor is...
Hello,
I am using NRF52840 with SDK 16.0.0 and Mesh SDK 4.1.0
.I am trying to use SAADC with BLE Mesh(SDK 4.1.0). I used default example of SAADC with multiple channel...
I am new to nRF9160 development board. I have just opened the board and tried to connect following the startup instructions. I was able to see LED 3 and LED 4 blink the first...
Hi all,
I am trying to get a hang of SES platform(Using the nRF52840 Preview DK, SDK 15.3) and it's my first few trails with it. I am trying something very basic now to...
I want to read characteristics (central needs read data from peripheral whenever he want ) but don’t want to use notification.
I am trying this with authorization but it...
