SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I have successfully upgrade 2 thingy 91 with the latest modem firmware 1.2 via MCUboot, and it worked.
I then tried to upgrade the existing standard application from 2019...
The nRF9160 v1.2.0 does not respond "OK" after AT+CFUN=0 !!!
2020-05-07T12:21:07.489Z DEBUG modem >> at+cfun=0\x0D\x0A 2020-05-07T12:21:08.489Z ERROR Error: 'at+cfun=0
Hi Devzone,
I am a beginner in BLE development. I have a nrf52840-dk and want to test the ble-app-uart example in SDK-16.0.0.
I firstly use NRF connect desktop programmer...
Hi,
I recently procured a nrRF52 DK board (PCA10040, v2.0.0 with nRF52832) for our new product development activity.
I tried following precompiled binaries present in...
Dear Nordic Tech Support & community,
The SDK 16.0.0 supports only one button long-push at time. Attached you can find a SDK-patch to add the support of multiple long-press...
Hi Team
I am trying to implement the firmware upgrade for master controller nrf52832 on chip using esp8266 over uart and I am very new with this boot-loader part.
I...
Hi
I had implemented a DFU module in esp8266 where I am trying to upgrade nrf over serial (UART Communication).
I had success with Init file write but when I send the...
Hi,
I am using nrf52833 EVB as an SPI master. The data is sent properly and well-received at the slave, however, I have a problem with the data received.
The problem...
Behaviour:
- Bluefruit the feater (nRF82832)
- Bluetooth BLE
- Implementation of Fitness Machine Service (0x1826)
- What is correct : all characteristics notified...
Hello, Nordic!
Our project is at evaluation stage. We aimed to build an Bluetooth 5.1 AoA indoor locator system, where the reciever should know the location of the transmitter...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
