Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Currently i am testing the nRF52840 Preview DK DFU function. Is the NRF52840 support by SoftDevice(S132)? and also match with the SDK(nRF5_SDK_v13.x.x) ?
thanks!
Hi,
is it possible to get some statistical information about a BLE connection?
Background is, that I'm experiencing connection problems (degrading throughput, stuttering...
I am using the Mesh-SDK v1.0.0, the device is the nRF52832xxAA on PCA10040-Boards with the Softdevice s132. I am new to the development with BLE, and specially mesh.
I have...
Hi
I would like to modulate the positive output of the UART using PWM
I know i can feed the UART and a PWM putput into a AND gate no problem, but im wondering if there...
Is there a ready example to run nRf51822 as a controller to external host via HCI commands over UART or USB?
e.g. I want to interface the Nordic chip with an open source...
I am using softDevice S140 with SDK 14.2.0_17b948a, working with the ble_app_blinky.
I need to be able to connect one peripheral device to multiple central devices (peripheral...
I connected via a USB cable my ppk to my computer. But when I fire up ppk.py, it says "no response from ppk. Check power, debugger connection and make sure the firmware is...
Is there any other way of programming the Nordic Thingy other than using the nrf52 DK? Where to get the programming/debugging port's pinout , I didn't find that in the hardware...
After connect devices status GAP Secure status ...->evt.gap_evt.params.auth_status.auth_status 0x0D In documentation absend this code = 0x0D What is It?
I would like to use 1.3 V System power to supply some external circuit that may need max 10 mA. This voltage is available via pin DEC4.
I expect that you are going to...
Hi There, I'm very new to mesh and have a bit of a learning curve to understand the mesh SDK. A few questions for those in the know....
I have been playing around with the...
hi,
can anyone share sample code for getting accel values from MPU9255.?
I have tried with this ,Iam not getting output.
Chip :nrf52382
Board : nrf52Dk - PCA10040...
Hi
How can i configure NRF_LOG with IAR and J-Link connected via USB to a RAK 813 BreakBoard, i'm testing BLE SCAN Application.
Regards,
Julio César Morales bErmúde
Is there a way to modify the code in the ios nrf beacon app to identify nordic beacons?
I am aware that the manufacturing id must be set to 0x004C in order to be identified...
