I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I'm trying to print received data on my com port but when I set the "NRF_LOG_ENABLED" as 1 the error below shows up.
What does it mean?? How would I know what files to...
Hi There,
I'm just getting started with ARM and the NRF52832. I've done a lot of work with 8-bit micros and I'm interested in learning 32-bit and in porting some old AVR...
I would like to use printf using ITM for debugging my application using a BL652 module (nRf52832).
I have followed the instructions in the Keil paper APNT_308. Printf is...
hi,
i am doing a project where i have to merge nrf mesh light switch server with mesh dfu example. i am using nrf mesh sdk v1.0.0 and nrf52832 mcu.
i have merged two programs...
I want to disable logging (which is working OK). In my app.config.h I have set the following:
#undef NRF_LOG_ENABLED
#define NRF_LOG_BACKEND_SERIAL_USES_UART 0
#define...
Desired behavior:
After a long press of the button, my desired behavior is to erase bonds and advertise and let another central pair and bond to the device.
After a normal...
Simultaneously, as a way of a parallel bus, using an extra one as a input clock, and save the byte in easydma, without CPU intervention?
Either in the nRF52832 or nRF52840...
Are there any options today that include Sub GHz, Bluetooth, and LTE for Mesh Networks??
I am thinking of a Gateway with multiple sensors communicating through Sub 1Ghz...
Hello,
We are trying to evaluate the HomeKit SDK with our nRF52832 BLE modules. The "Lock(static)" sample application doesn't work with Apple 'Home' App on iPhone 8+. The...
I'm currently evaluating different platforms, that run on the nrf52832 soc, like Nordic Semiconductors own firmware, as well as Zephyr, myNewt and mBed. As you guys from ...
Dear sirs
Good evening !
I´m using the RF24.h library in order to develop a system that comunicates in peer-to-peer mode.
When I transmit 3 bytes towards a receiver...
I'm hoping someone can tell me if I'm on the right track. Do I understand correctly that on an nrf51, the LPCOMP can be configured to wake the processor on an analog input...
Hello,
I was wondering how is calcualted or read on the Thingy firmware the variable w for the quaternion used in the Gyroscope readings.
Looking into m_motion.c in the...
The power data of lfclk is measured under the same hardware and software conditions. When we used two model chips, we found a difference of 1 microamps for the value of the...
hi, I am trying to make buttonless dfu working, but I am not sure how to do that. I am using SDK 14.2.0 with nrf52832. right now, the ble dfu example works. and I found in...
