Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi
I am trying to get get the ble_app_template running on my PCA20006 beacon kit (nRF51822 xxAC) using a j link edu .
I have imported the ble_app_template_pca10028_s130...
I'm new to using the Nordic SDK and I'm trying to use the BLE template to start my own service. Is there a walk-through for doing this somewhere that may be able to help?...
Hello,
I'm developing a simple code that make use of timers using NRF-based boards and Arduino code.
The following code works fine on a Simblee nRF51822 board , but...
I was trying to install firmware into my nRF51 Dongle using jlink.exe on Windows, so I can use nRF Sniffer. I made the mistake of unplugging the dongle from USB after erasing...
I have an nRF52832, coding with SEGGER and the SDK 14.2.0. I'm trying the ble_peripheral/ble_app_uart example (although I get similar results with the other BLE examples)...
Using a pushbutton while advertising, the GPIOTE_IRQHandler handles the pushbutton click OK, but then the processor resets. The RESETREAS is code 4, aka. RESET from soft reset...
Hi,
I have couple of queries that need to be sorted,
http://www.nordicsemi.com/eng/Products/S112-SoftDevice, Says that S112 supports 2-peripheral connection and 1 broadcaster...
I want advertise the peripheral periodically only. i implement the logic it is working fine.but my doubt is once i connected to connected to central device advertise is no...
Noted the difference between the layouts concerning antenna matching among DK 0.9 and DK 0.11.
DK 0.9
DK 0.11
The screenshots are for L3. Differences between...
Hello,
I have a requirement to implement the following functionality. Can this be done?
Basically i need to store some customer info on the NFC NTAG. This has to customizable...
I am using nRF Connect for desktop v2.3.0. In my DIS service Firmware Revision String characteristic I am using a string of 30 characters. But when I connect to my device...
Hi,
We are looking into developing a device based on 52832 platform.
How many devices (phones) can be paired with our device?
In other words: How many pairing keys can...
See attachment - enlarge if it's too small. How can I get nRF Connect on my Windows 10 laptop to bring more than 20 characters, and also print in text (instead of hex values...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
