Note: I am aware that NCS v3.4.0 recommends DTS-based partitioning over Partition Manager. However, I was unable to get the DTS-based approach working for my specific configuration...
Due to the great advice & guidance from Nordic 3 years ago (Andreas Haugland & Vidar Berg), see:
and https://devzone.nordicsemi.com/support/311747 we have been happily using...
Problem Description
The custom hardware board cannot boot normally after flashing the firmware. However, the exact same firmware image works perfectly on the official nRF54L15...
For my project I want MCUboot with the upgrade image placed in the external flash, and TF-M. I am not able to get this combo to boot however, and I suspect the reason is that...
Hi!
I am trying to do a DFU with external flash, using a nRF54L15-DK development kit.
To evaluate this feature, I use the l9_e3_sol example available on GitHub (I use...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I'm having problems running the ble_peripheral/ble_app_blinky example with my iPhone 7 and nRFConnect. Here are the specs for the tools I'm using:
nRF52-DK: PCA10040...
Hi all,
I am currently trying to develop my own Secure BLE DFU bootloader from the example provided in the SDK 12.3.0. I don't work on the DK, I have my own board with a...
Hi I've got two nrf51 dongles that i would like a communication path between (ble) to transfer numbers only. I am a student, and these bluethooth products are new to me. I...
Hi,
I'm using Nordic SDK version - nRF5_SDK_14.2.0_17b948a and Dev Board - PCA10056 V0.9.0 2017.10 - 683871638
USB serial driver is not detected on Windows 8.1 Pro while...
hi everyone
i need some help, when i scan my device with my smartphone every things is well but there is something weird i usually find two services with the same uuid instead...
Hi,
I'm wondering if your SDK15 and S140 v6.0 will have support for your IOT SDK when it is released? If so, will it also include examples for nrf52840?
Thank you
...
I tried to use UART both for NRF_LOG and NRF_CLI. Now it's running but I had a problem that calling to nrf_cli_init caused fatal error 8 - INVALID_STATE.
When I commented...
i have question about nRF52832's bluetuth. xtal is 32M, Cload is 12pf, but the frequency is 2.402199G(tested by Network Analyzer), Frequency differency is 199K. We find that...
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
