Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi
I purchased the full NRF8002 kit I am searching for the source code for the nRF Toolbox app but I am not able to download source code. Is the source code available for...
Hi,
I need something that can be the Master and talk to the Evaluation Kit Board to try to send a large amount of data. Do the Master Control Panel, or the mobile app nRF...
Hi,
I am using the nRF6310 + PCA10005 +nRFgo Studio as the lower tester, the supplied python scripts as the upper tester, and my own custom board as the DUT.
I've looked...
Hello, I am working with nrf51822 on my pcb design by myself, I read temperature from chip, the result is about 90deg, (I have div by 4 for 0.25 deg) it is impossible for...
Is there a way I can tell which version of the chip I'll get from a distributor? It's not clear to me that I can tell, from, eg the Mouser product page which rev it is. Is...
Hi,
I am working on proximity android application, i implemented immediate alert service, which is working fine. Now i need to set the alert level on the tag for linkloss...
Hi
I am working with alert notification example. I just wanted to know how you have tested the alert notification client example implementation. Is it just by using the...
Section 28.9.9 of the nrf51 reference manual shows the Config register has 3 defined bits, BBA. A is for Hardware Flow Control and is one bit, 0 or 1, which makes sense. ...
Hi,
I'm trying to add more user services to LBS demo. I generated 128b UUIDs for my services. Then I should add them to list returned by scan response in function advertising_init...
Hello!
Sorry for a new guy's description.
We had a device running in normal firmware application mode, and the Bootloader was programed. It's our goal to accomplish DFU...
Hello
I am using the nRF8002 kit. I would like to inform the host (Android app) when there is a long button press on the input pin.
Is this possible and if so which BLE...
Hi folks,
I was wondering if someone has a reference implementation of a bootloader that uses exclusively ANT technology to make DFUs, being it ANT-FS or any other alternative...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
This is something for the legal department.
You had some questions here about the RFduino before. This question is about legal obligations Nordic supposedly imposed on...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
