It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello,
I'm stuck in DFU using HCI(serial)..
I'm using nrf51822 , softdevice s110 ver 6.0.0 . I used example code in
"nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\device_firmware_updates...
Hi All,
I have a nrf52 PCA10040 Kit with me . I loaded the BLE app UART Central example binary into my Kit . The LED 1 is blinking (Scanning Indication) But am not getting...
I went though steps point here Everything went well. We create bootloader settings hex file base on our application hex file I'm a little confusing now. Should I always create...
Hi dev team,
in my design I am using the nRF52832.
On the GPIOs (P0.14,P0.15) I've connected a Darlington Array ( ST ULN2001 ).
My circuit is living of a super cap...
I coded following
BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS(&cccd_md.read_perm);
BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS(&cccd_md.write_perm);
char_md.char_props.notify = 1;...
Hi,
What does it means number 0x1D in p_ble_evt->header.evt_id in ble_db_discovery_on_ble_evt ?
I didn't get any error code, but service discovery is not completed.
Is...
I've noticed that Wireshark seems to occasionally report malformed data.
The malformed data seems to happen about 10% of the time and comes from all my smart beacons.
...
I am a beginner in the study of Bluetooth, and I have difficulty in understanding the purpose of API functions Bluetooth stack. For a better understanding of the system API...
I'm using MCP 3.1 and tried flashing the dongle from it multiple times. I also tried reinstalling MCP, but to no avail. When I flash some Blinky example using mbed it works...
I want to read whole flash memory using for loop and see how long it takes. What i have noticed is that it does not print all the lines. On the other side i ask myself: Does...
Hi,
I am very new to nRF51822 controller. i got some problem with compilation.
i have downloaded SDK v10.0xx and tried to compile blink example from following path.
...
Using Segger Embedded Studio 310i in Linux and SDK12.2.0, I imported the Beacon example project (ble_peripheral/ble_app_beacon) from Keil. Right now I'm trying to make it...
Hello everybody,
RTC0 is used by the SoftDevice. Is it possible to use the current RTC0 counter value as a system time, so that RTC1 doesn't have to run additionally? For...
I created a service with several characteristic values. I can read the values without any problem with the Master Control Panel on my Android tablet, but reading from the...
