I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
I need to send data from PC (windows 10) to nrf52832 using UART (hardware) in order to retransmit this data through mesh network with light switch example.
Do i need to...
Because I'm using PTR9618 module of nRF52832, it don't have XTAL 32.768Khz (X2).
When Makefile have NRF52_WITHOUT_SOFTDEVICE=1, hello-world, blink-hello work fine. But when...
Hi,
I'm looking to generate a clock signal on a gpio with an exact frequency. I tried this by setting the pwm base clock and adjusting the top value but got no luck.
Is...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
dear sir
i had use the ble_ant_app_hrm demo to test ant+ble,but i could not find the softdevice in the folder,so i can't connect it to my mobile phone,the link address is...
Hi, I'm using Central multilink example to connect with our Custom Peripheral sensors. I'm using board PCA10040, nRF52832, SDK_14.2.0, s132. Sensors have a custom service...
For NRF51 and NRF52 antenna matching network, is there any requirements for resitors? Tolerance?
I know there are some requirement for capcitor and inductor types, how...
Hello,
Can we combine a 5-certified hardware circuit with a softdevice that is 4.2-certified? (at examble mbn52832 (module) with s332 (Softdevice))
If yes, with which...
Hello dear
I have a question about NFC on RF52832. On section 42 of datasheet, says:
"The NFCT peripheral (referred to as the 'NFC peripheral' from now on) supports communication...
hello support team,
i have seen thread and sdk14.2.0/examples/peripheral/SAADC example
pca board: PCA10040
can anyone suggest how to read battery status using handler...
Hi,
I am trying to set an nrf52840 pdk (with SDK14 and s140_nrf52840_5.0.0-2.alpha) as peripheral and central at the same time and another nrf52840 pdk just as a peripheral...
Hi,
I play with pca10040 and the light-switch example from SDK for Mesh v1.0.1. Everything works but I wonder why the advertising signals are not seen by nRF-Connect Scan...
