Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi All,
We have build a BLE beacon device based on the nrf52 chip. The device works fine but we would like to get a finer control over the TX power since it is used for...
compiled nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_rscs example but will fail on adding chararteristics in char_add() setup: SEGGER Embedded Studio for ARM Release...
Hi guys,
I am trying to use a TM2001 amplifier ( Taiwan Microelectronics, google returns the PDF) to amplify the signal from an nRF24L01P.
The TM2001 seems to accept a...
Hi.
I want to create Bluetooth mesh network and I need that each of device at first must be provisionee, but if in a minute it hasn't been added in a network by provisioner...
Hi
I was designing a custom board for nrf52832. The 32MHZ crsytal mentioned in the refrence design of nrf52832 is not available on digi key. So I am ordering the below given...
Hello,
I have a string data and I want to get a part of it which start for example with "hello" and I want to get 20 characters after "hello".
(for more details I'm using...
in the demo of EnOcean switch translator client,there is just enocean_switch_nrf52832_xxAA_s132_6_0_0.emProject .is it use the same demo as client in the example of light...
Hi, I am using nrf SDK for mesh and try to add FreeRTOS , but after adding build failed because both has files with same name. Is it possible to work with FreeRTOS and nrf...
Hello;
I want to scan beacon devices (UUID infos) every second with Arduino Uno + nRF51822
I could not find a sample on the site. (Arduino Code)
Is it possible? Would...
I've gotten a good handle on how Gazell interacts with devices and the host, but I am running into an issue where there are higher rate of failures when using two devices...
I am using the proxy server and the proxy client example
Initially Proxy Client and Proxy Server are present in MESH network. Once the Proxy Client recycle the power ...
What was the reason for not making the context available for saadc-handlers?
Most handlers I stumbled on (twi and timer) either had a void* p_context or void* p_user_data...
Hi,
We are using nordic nRF52832 in our project as per our requirement we have to implement sleep and wake up mode with the help of button interrupt.our use case is that...
