hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
I have the preprocessor define CONFIG_NFCT_PINS_AS_GPIOS in my code, and GPIO functionality for P0.09 and P0.10 are working just fine for me...
My issue is that even when...
Hello!
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
I want to send advertisings at regular intervals (every second...
Hi,
Is it possible for an 3 party BLE device like an mobile device like an Android/IOS Phones or ESP etc to participate in mesh notwork if so is there any documentation...
I have been unable to perform a DFU over BLE using the bootloader_secure_ble example.
I am using SDK 14.0, nRF52832, S132 with a custom board, along with the nRF51 Development...
Hello,
I want to factory pair nRF52 to nRF52 connections (NUS) with a factory set key but i'am lost.
I digged in NFC pairing but it's too complicated for my understanding...
Hello,
i use IAR EWARM 8.20.2 and SDK 12.3.
I compiled the blank Blinky example from the SKD for the pca10040 without any Errors or Warnings. When i load the .hex to the...
I use IAR EWARM 8.20.2 and the SDK 12.3 because i want to use the S130 for the nRF51.
I installed the provided MDK_8_11_1_IAR and now there are two options for Nordic Semiconductor...
